SIIG Network Card 04 0835A User Manual

DP Wireless-N PCI  
Express Wi-Fi Adapter  
Quick Installation Guide  
Introduction  
The DP Wireless-N PCI Express Wi-Fi Adapter is  
designed to add a wireless connection to your  
PCI Express equipped desktop computer.  
Key Features and Benefits  
Complies with 2.4GHz IEEE 802.11 b/g/n  
standards  
2T2R with 300Mb/s data rate for both  
transmitting and receiving  
Wireless security: 64/128bit WEP, WPA,  
WPA2  
Supports WPS (WiFi protected setup)  
Supports Qos-WMM, WMM-PS  
Installs in standards height or low profile  
chassis with included brackets  
04-0835A  
1
 
Layout  
Status LED  
Anttennas  
Figure 1: CN-WR0811-S1 Layout  
Status LED  
Lnk/Act on: Indicates valid connection.  
Lnk/Act quickly flashing: The adapter is  
transmitting or receiving data.  
3
 
HardwareInstallation  
General instructions for installing the card are  
provided below. Since the design of computer  
cases and motherboards vary, refer to your  
computer’s reference manual for further  
information, if needed.  
Static Electricity Discharge may permanently  
damage your system. Discharge any static  
electricity build up in your body by touching your  
computer’s case for a few seconds. Avoid any  
contact with internal parts and handle cards  
only by their external edges.  
Note: For low profile chassis, remove the  
standard height bracket and install the  
enhanced low-profile bracket now.  
1.  
2.  
3.  
Turn OFF the power to your computer and  
any other connected peripheral devices.  
Unplug the power cord and remove the  
cover from the computer.  
Remove the slot bracket from an available  
PCIe slot.  
Do4wnload from Www.Somanuals.com. All Manuals Search And Download.  
4.  
To install the card, carefully align the card's  
bus connector with the selected PCIe slot on  
the motherboard. Push the board down  
firmly, but gently, until it is well seated.  
Replace the slot bracket's holding screw to  
secure the card.  
Replace the computer cover and reconnect  
the power cord.  
Attach the external antennas to PCIe  
adapter antenna ports.  
5.  
6.  
7.  
SoftwareInstallation  
NOTE: Server 2008 & 2008 R2 Microsoft WLAN  
AutoConfig Service is not installed by default.  
Follow the instructions below to install WLAN  
AutoConfig Service to enable wireless network  
support. After completing the installation, and  
for all other Windows OS, go directly to Driver  
Installation on page 7.  
1.  
2.  
Right click Computer, then click Manage.  
Right click Features, then click Add  
Features.  
5
 
3.  
Check the Wireless LAN Service, then  
click Next.  
Figure 2  
4.  
Click Install then click Close, and Wireless  
LAN Service is installed successfully.  
Figure 3  
Do6wnload from Www.Somanuals.com. All Manuals Search And Download.  
DriverInstallation  
Follow the instructions below to install the driver.  
1.  
2.  
Install the board and boot up Windows.  
At the Found New Hardware, click Cancel.  
Skip this step if not prompted.  
3.  
Insert the driver CD. At the prompted CD  
driver window, select folder PCIe, then  
double click Setup. Or press Windows key  
and R, then type D:\PCIe\Setup.exe in  
the Run window, then click OK. (Change  
D: to match your CD/DVD-ROM drive  
letter)  
4.  
5.  
Click Yes or Allow at the User Account  
Control. Skip this step if not prompted.  
At the license Agreement, select I accept  
the terms of the license agreement, click  
Next.  
6.  
7.  
Select Install the driver and Ralink WLAN  
Utility, then click Next.  
SelectRalinkConfigurationTool,thenclick  
Next.  
8.  
9.  
Click Install, then click Finish.  
Restart the computer.  
7
 
To Verify Windows Installation  
1.  
Go to Device Manager to verify installation.  
For Window 8 / Windows 7 / Windows XP /  
Server 2003 / 2008 R2: Right click Computer  
or My Computer, click Manage, then click  
Device Manager.  
For Windows Vista: Right click Computer,  
click Manage, click Continue, then click  
Device Manager.  
For Server 2008: Right click Computer, click  
Manage, double click Diagnostics, then  
click Device Manager.  
2.  
Double click Network adapters. A 802.11n  
Wireless LAN Card should be displayed.  
Wireless Network Configuration  
After finishing the driver installation, use  
Windows Zero Configuration (WZC) OR Ralink  
Wireless Utility (RaUI) to connect to your wireless  
network.  
When WZC is chosen as the configuration tool,  
RaUI only provides monitoring functions, and  
vice versa.  
Do8wnload from Www.Somanuals.com. All Manuals Search And Download.  
Right click the RaUI icon in the taskbar, then  
select Use Zero Configuration as Configuration  
Utility to configure by WZC, or select Use  
RaConfig as Configuration Utility to configure  
by RaUI. For Window 8, Windows 7, Vista, WZC  
and RaUI can be used together and no need to do  
the selection.  
Figure 4  
WZC (recommended)  
WZC is the recommended tool to use. Right click  
the wireless network icon in the taskbar, then  
select View Available Wireless Networks.  
Figure 5  
9
 
At the Wireless Network Connection, double  
click the preferred wireless network, enter the  
Network key, click Connect, then click Connect  
Anyway.  
Click Continue Anyway  
Figure 6  
For advanced settings, click Change advanced  
settings, select tab Wireless Networks, then click  
Properties (as Figure 7 & 8).  
Do10wnload from Www.Somanuals.com. All Manuals Search And Download.  
Click Change advanced settings  
Figure 7  
Click Properties  
Figure 8  
 
11  
Select the type of Network Authentication and  
Data Encryption, click OK to save the settings.  
Figure 9  
Do12wnload from Www.Somanuals.com. All Manuals Search And Download.  
Ralink UI  
Note: If you configured your wireless network  
using WZC utility on page 9, this utility is not  
needed.  
Double click the Ralink icon in the task bar. Click  
the icon  
to bring up the AP list.  
Click the icon to bring up the network AP list  
Figure 10  
Double click the the preferred AP from the AP  
list, and the Profile Settings section is displayed.  
Select the Authentication and Encryption type,  
then click the arrow  
to go to the next step. See  
Figure 11 on the next page.  
13  
 
Select the Authentication and Encryption type, then click the arrow to the next step.  
Figure 11  
Enter the WPA Preshared Key, then click the  
arrow icon  
.
Figure 12  
Once the wireless network is successfully  
connected, the RaUI icon turns to green  
the Windows network shows connected  
,and  
.
Do14wnload from Www.Somanuals.com. All Manuals Search And Download.  
TechnicalSupportandWarranty  
QUESTIONS? SIIGs Online Support has answers! Simply visit our web site at  
www.siig.com and click Support. Our online support database is updated daily with  
new drivers and solutions. Answers to your questions could be just a few clicks away.  
You can also submit questions online and a technical support analyst will promptly  
respond.  
SIIG offers a 5-year manufacturer warranty with this product. This warranty covers the  
original purchaser and guarantees the product to be free of any defects in materials or  
workmanship for five (5) years from the date of purchase of the product.  
SIIG will, at our discretion, repair or replace (with an identical product or product  
having similar features and functionality) the product if defective in materials or  
workmanship. This warranty gives you specific legal rights, and you may also have other  
rights which vary from state to state. Please see our web site for more warranty details.  
If you encounter any problems with this product, please follow the procedures below.  
A) If it is within the store's return policy period, please return the product to the store  
where you purchased from.  
B) If your purchase has passed the store's return policy period, please follow the steps  
below to have the product repaired or replaced.  
Step 1: Submit your RMA request.  
Goto www.siig.com, clickSupport,then REQUESTAPRODUCTREPLACEMENT  
to submit a request to SIIG RMA or fax a request to 510-657-5962. Your RMA request  
will be processed, if the product is determined to be defective, an RMA number will  
be issued.  
Step 2: After obtaining an RMA number, ship the product.  
Properly pack the product for shipping. All accessories that came with the  
original package must be included.  
Clearly write your RMA number on the top of the returned package. SIIG will  
refuse to accept any shipping package, and will not be responsible for a product  
returned without an RMA number posted on the outside of the shipping  
carton.  
You are responsible for the cost of shipping to SIIG. Ship the product to the  
followingaddress:  
SIIG, Inc.  
6078 Stewart Avenue  
Fremont, CA 94538-3152, USA  
RMA #:  
SIIG will ship the repaired or replaced product via Ground in the U.S. and  
International Economy outside of the U.S. at no cost to the customer.  
15  
 
About SIIG, Inc.  
Founded in 1985, SIIG, Inc. is a leading manufacturer of IT connectivity  
solutions (including Serial ATA and Ultra ATA Controllers, FireWire, USB,  
and legacy I/O adapters) that bridge the connection between Desktop/  
Notebooksystemsandexternalperipherals. SIIGcontinuestogrowbyadding  
A/V and Digital Signage connectivity solutions to our extensive portfolio.  
SIIGproductsoffercomprehensiveusermanuals,manyuser-friendlyfeatures,  
andarebackedbyanextensivemanufacturerwarranty. Highqualitycontrol  
standards are evident by the overall ease of installation and compatibility of  
ourproducts,aswellasoneofthelowestdefectivereturnratesintheindustry.  
SIIG products can be found in computer retail stores, mail order catalogs,  
throughmajordistributors,systemintegrators,andVARsintheAmericasand  
theUK,andthroughe-commercesites.  
PRODUCT NAME  
DP Wireless-N PCI Express Wi-Fi Adapter  
FCC RULES: TESTED TO COMPLY WITH FCC PART 15, CLASS B  
OPERATING ENVIRONMENT: FOR HOME OR OFFICE USE  
FCCCOMPLIANCESTATEMENT:  
This device complies with part 15 of the FCC Rules. Operation is subject  
to the following two conditions: (1) This device may not cause harmful  
interference, and (2) this device must accept any interference received,  
including interference that may cause undesired operation.  
THE PARTY RESPONSIBLE FOR PRODUCT COMPLIANCE  
SIIG, Inc.  
6078 Stewart Avenue  
Fremont, CA 94538-3152, USA  
Phone: 510-657-8688  
DP Wireless-N PCI Express Wi-Fi Adapter is a trademark of SIIG, Inc. SIIG and the SIIG logo  
are registered trademarks of SIIG, Inc. Microsoft and Windows are registered trademarks of  
Microsoft Corporation. All other names used in this publication are for identification only  
and may be trademarks of their respective owners.  
September,2012  
Copyright© 2012 by SIIG, Inc. All rights reserved.  
 

Sharp Computer Monitor LL T17A3 User Manual
Shindaiwa Vacuum Cleaner 82052 User Manual
Singer Sewing Machine 1021 User Manual
Singer Sewing Machine AJ047664 User Manual
Sony Cassette Player TCM 20DV User Manual
Sony Microphone PSP 240 X User Manual
Sony Portable Speaker SRS A47 User Manual
Sony Radio SRF DR2000 User Manual
StarTechcom Laptop Docking Station UNIDOCK2U User Manual
SVAT Electronics DVR CVP800 User Manual