Sharp Calculator EL 530V User Manual

ENGLISH  
DISPLAY  
SCIENTIFIC CALCULATOR  
Symbol  
MODEL  
EL-530V  
OPERATION MANUAL  
Exponent  
Mantissa  
PRINTED IN CHINA  
04AGK (TINSE0506THZZ)  
All symbols will not be displayed simultaneously, as shown  
above.  
Certain inactive symbols may appear visible when viewed  
from a far off angle.  
: Appears when the entire equation cannot be dis-  
played. Press </> to see the remaining (hid-  
den) section.  
/
INTRODUCTION  
Thank you for purchasing the SHARP Scientific Calculator  
Model EL-530V. This calculator will help you understand math-  
ematical concepts behind fraction calculation, such as simpli-  
fication and reduction.  
After reading this manual, store it in a convenient location for  
future reference.  
2ndF : Appears when @ is pressed, indicating that the  
functions shown in orange are enabled.  
SIMP : Indicates that a fraction can be simplified further, or  
expressed with a lower denominator.  
: Appears when statistical mode is selected.  
: Indicates that a numerical value is stored in the  
independent memory.  
M
Operational Notes  
Do not carry the calculator around in your back pocket, as it  
may break when you sit down. The display is made of glass  
and is particularly fragile.  
Keep the calculator away from extreme heat such as on a  
car dashboard or near a heater, and avoid exposing it to  
excessively humid or dusty environments.  
Since this product is not waterproof, do not use it or store it  
where fluids, for example water, can splash onto it. Rain-  
drops, water spray, juice, coffee, steam, perspiration, etc.  
will also cause malfunction.  
BEFORE USING THE CALCULATOR  
Key Notation Used in this Manual  
In this manual, key operations are described as follows:  
To specify π : @V  
To specify Exp : E  
Clean with a soft, dry cloth. Do not use solvents or wet  
cloth.  
Do not drop it or apply excessive force.  
To access functions printed in orange above keys, press @  
first.  
Never dispose of batteries in a fire.  
In this manual, number entry examples are shown with ordi-  
nary numbers (i.e., “100” will be indicated instead of  
100”).  
Keep batteries out of the reach of children.  
This product, including accessories, may change due to  
upgrading without prior notice.  
SHARP will not be liable nor responsible for any incidental  
or consequential economic or property damage caused by  
misuse and/or malfunctions of this product and its periph-  
erals, unless such liability is acknowledged by law.  
Power On and Off  
Press N to turn the calculator on, and @F to turn it  
off.  
Clearing the Entry and Memories  
Press the RESET switch (on the back), with the tip of a ball-  
point pen or similar object, only in the following cases. Do  
not use an object with a breakable or sharp tip. Note that  
pressing the RESET switch erases all data stored in  
memory.  
There are three clearing methods as follows:  
Clearing  
Entry  
(Display)  
M*1  
STAT, ANS*2  
operation  
When using for the first time  
After replacing the batteries  
To clear all memory contents  
If an abnormal condition occurs and all keys are  
inoperative.  
N
@c  
RESET  
×
×
×
If service should be required on this calculator, use only a  
SHARP servicing dealer, SHARP approved service facility, or  
SHARP repair service where available.  
: Clear  
Independent memory M.  
Statistical data and last answer memory.  
× : Retain  
1
*
*
2
To clear the independent memory (M), press NO.  
Hard Case  
Entry and Correction of an Equation  
Press < or > to move the cursor.  
To return to an equation after getting the answer, press  
< (>).  
To delete a number, place the cursor on the number to be  
deleted, then press d.  
To insert a number, move the cursor to the place immedi-  
ately after where the number is to be inserted, then enter  
the number.  
 
SCIENTIFIC CALCULATIONS  
15 + 8  
15 – 3  
N 15 + 8  
15+8_  
Select the normal mode.  
<<dd  
15_  
15–3_  
In each example, press N to clear the display before  
- 3  
performing the calculation.  
13 × 24 =  
N 13 * 24 =  
312.  
Arithmetic Operations  
<(>)  
13×24  
360.  
15 × 24 =  
>d 5 =  
12+16×3=  
N 12 + 16 * 3 =  
350 - 120 / 4 =  
60.  
350–120÷4=  
320.  
Priority Levels in Calculation  
This calculator performs operations according to the following  
72×(-12)–150= 72 *– 12 - 150 =  
–1014.  
priority:  
1 Functions expressed with numerical data placed before  
(5+21)×(30–16)= ( 5 + 21 )*  
(such as x2, x3)  
( 30 - 16 )=  
364.  
2 yx, x  
3 π  
y
¿
3
-4  
(6×10 )÷(2×10 )=( 6 E 3 )/  
4 Functions expressed with numerical data placed after (such  
( 2 E– 4 )=  
30000000.  
as sin, cos)  
5 Multiplications with the sign “×” omitted from the front of a  
function (such as 3cos20)  
Constant Calculations  
6 ×, ÷  
7 +, –  
In constant calculations, the addend becomes a constant.  
Subtraction and division are performed in the same manner.  
For multiplication, the multiplicand becomes a constant.  
After performing calculations using constants, on pressing  
<(>) to edit an equation, the constants will be  
displayed as K.  
8 Operations end commands (such as =, M+, %, DATA, CD)  
A parenthesized calculation section has precedence over  
other sections of the calculation.  
245+60=  
12+60=  
N 245 + 60 =  
305.  
72.  
INITIAL SETUP  
N 212 + 60 =  
Mode Selection  
150–20=  
250–20=  
150 - 20 =  
130.  
230.  
Normal Mode:  
250 - 20 =  
Used to perform arithmetic operations and function calcula-  
tions.  
200÷4=  
180÷4=  
200 / 4 =  
50.  
45.  
180 / 4 =  
Statistical Mode:  
15×3=  
15×10=  
15 * 03 =  
45.  
150.  
Used to perform statistical operations. To enter statistical  
mode, press @”. appears on the display to  
indicate that the statistical mode is selected. To return to  
normal mode, press @” with on the display.  
disappears as the calculator returns to normal mode.  
The mode will remain selected when the calculator is turned  
off.  
When executing mode selection, last answer memory will  
be cleared.  
15 - 10 =  
Functions  
For each example, press N to clear the display.  
The results of inverse trigonometric functions are displayed  
within the following ranges:  
θ = sin-1x, θ = tan-1x  
θ = cos-1x  
–90° ≤ θ ≤ 90°  
≤ θ ≤ 180°  
Selecting the Display Notation and Decimal  
Places  
This calculator has two display notation systems for displaying  
calculation results: floating point system and fixed decimal  
point system.  
sin30° =  
cos60° =  
tan45° =  
Ns 30 =  
u 60 =  
t 45 =  
0.5  
0.5  
1.  
When the fixed decimal point system is selected, the number  
of decimal places can be set to any value between 0 and 9.  
The last decimal digit will be rounded off.  
–1  
sin 0.5 =  
@S 0.5 =  
@U 0.5 =  
@T 1 =  
30.  
60.  
45.  
34.  
512.  
–1  
cos 0.5 =  
Use @fl to switch to the fixed decimal point system,  
press @i, then enter a value between 0 and 9 to set  
the decimal placement.  
–1  
tan 1 =  
2
2
3
+ 5  
=
=
3 @L + 5 @L=  
8 @¤=  
32 + 3 @$ 21 =  
The number will be displayed in scientific notation if the  
calculation results for floating point system does not fit in  
the following range:  
3
8
3
32 + 21 =  
0.000000001 | x | 9999999999  
8.415778426  
2401.  
1 ÷ 3 =  
[Floating point]  
4
7
=
7 @™ 4 =  
N 1 / 3 =  
0.333333333  
0.333333333  
0.33  
[Fixed decimal point] @fl  
π
– =  
@V/ 3 =  
1.047197551  
3
[TAB set to 2]  
@i 2  
[Floating point]  
@fl  
0.333333333  
 
Chain Calculations  
1
1
– + – =  
4 + 5 @¨=  
0.45  
This calculator allows the previous calculation result to be  
used in the following calculation.  
4
5
The previous calculation result will not be recalled after  
entering multiple instructions.  
In the case of utilizing postfix functions (¿ , sin, etc.), you  
can perform a chain calculation even when the previous  
calculation result is cleared by the use of the N or @  
c keys.  
200 × 32% =  
200 * 32 @%  
64.  
50.  
150 ÷ 300 = ? % 150 / 300 @%  
200 + (200 × 32%) = 200 + 32 @%  
300 – (300 × 25%) = 300 - 25 @%  
264.  
225.  
6+4 = ANS  
ANS + 5  
N 6 + 4 =  
10.  
15.  
+ 5 =  
Random Function  
This calculator has three random functions. Press N to  
8 × 2 = ANS  
8 * 2 =  
16.  
256.  
2
exit.  
ANS  
@L=  
Random Numbers  
44+37 = ANS  
44 + 37 =  
81.  
9.  
A pseudo-random number, with three significant digits from 0  
up to 0.999, can be generated by pressing @`=.  
To generate the next random number, press =.  
ANS =  
⁄=  
Random Integer  
Integer number between 0 and 99 can be generated randomly  
by pressing @›=. To generate the next integer  
random number between 0 and 99, press =.  
Calculating the Highest Common Factor  
(H.C.F.) or Lowest Common Multiple (L.C.M.)  
To calculate the H.C.F. or the L.C.M., the procedures are as  
follows:  
Random Dice  
To simulate rolling dice, integer number between 1 and 6 can  
be generated randomly by pressing @fi=. To  
generate the next integer random number between 1 and 6,  
press =.  
What is the H.C.F. N 24  
24_  
24HCF36_  
12.  
of 24 and 36?  
@‹ 36  
=
What is the L.C.M. N 15  
15_  
15LCM9_  
45.  
Memory Calculations  
of 15 and 9?  
9  
This calculator has two memory allocations: independent  
memory (M), and last answer memory (ANS). You will find  
them especially useful when combinations of calculations be-  
come complicated, or when applying the answer of previous  
calculation to another operations.  
=
“Highest Common Factor” is synonymous with “Greatest  
Common Factor”, “Lowest Common Multiple” is with “Least  
Common Multiple”.  
Press NO to clear the independent memory (“M”  
symbol will disappear).  
Calculating quotient and remainder  
: Calculates the quotient and remainder.  
After pressing R to recall a value stored in the memory,  
the value as displayed will be used in the calculation.  
Independent memory (M)  
23 ÷ 5  
(R: Remainder)  
N 23 @“ 5  
235_  
O : Stores the result in the memory.  
R : Recalls the value stored in the memory.  
@; : Adds the result to the value in the memory.  
=
4.  
2.  
6.  
R3.  
9.5 ÷ 4  
9.5 @“ 4  
9.54_  
=
R1.5  
–32 ÷ (–5)  
32 @“– 5  
–32–5_  
M
M
M
N 3 * 5 O  
15.  
45.  
60.  
=
R–2.  
30 + (3 × 5) =  
30 +R=  
(3 × 5) × 4 =  
R* 4 =  
Pressing cannot be followed by pressing a key for  
M
M
M
M
M
another operation such as (+, –, ×, ÷), otherwise an error  
20+10–5=  
121+13×2=  
+) 21×3–16=  
(Total)  
N 20 + 10 - 5 O  
121 + 13 * 2 @;  
21 * 3 - 16 @;  
R
25.  
147.  
47.  
219.  
0.  
will result.  
The calculator can display a quotient or remainder up to 5  
digits in length, including the “–” sign. If numbers longer  
than 5 digits are entered, normal division is performed.  
NO  
Last answer memory (ANS)  
When = is pressed, the calculation result will automati-  
FRACTION CALCULATIONS  
cally be stored in the last answer memory.  
@? : Recalls the value stored in the last answer  
Entering Fractions  
memory.  
To enter fractions, use the following keys:  
Ø : Places the symbol “ ” between the numerator  
and the denominator.  
/
4 ÷ 5 = 0.8…(A) N 4 / 5 =  
4 × (A) + 60 ÷ (A) = 4 *@?+ 60 /  
@?=  
0.8  
: Separates the integer (whole number) part from  
78.2  
the fractional part of a mixed number.  
 
*
Enter a common denominator for the two fractions.  
If the entered value is not a common denominator, the  
cursor will be set under the value. Press d to clear the  
value, then enter a correct common denominator. Press  
N to return to the “DENOM.?” display.  
2
4– =  
3
N 2 Ø 3 =  
4 1 Ø 2 =  
2/3  
1
4– =  
4¬1/2  
2
Up to 10 key strokes, including “¬” and “  
/
”, can be used to  
Now that you have learned how to reduce a fraction to its  
lowest denominator, you can start using your calculator  
to perform fraction calculations quickly and efficiently.  
enter a fraction.  
Calculating with Fractions  
Fractions can be incorporated into an arithmetic calculation.  
The “SIMP” symbol will appear with a calculation result if the  
answer can be further simplified. Refer to the following sec-  
tion of this manual for details.  
1
1
4
– + – =  
N 1 Ø 3 + 1 Ø 4  
1/3+1/4_  
3
ªDENOM.? SIMP 28/48  
=*  
=
=
12_SIMP 28/48  
4/12+3/12_  
7/12  
1
1
– + – =  
N 1 Ø 2 + 1 Ø 3 =  
5/6  
2
2
3
1
*
If = is pressed instead of a number entry, the lowest  
× – =  
2 Ø 5 * 1 Ø 3 =  
2/15  
5
3
common denominator will automatically be displayed.  
Convºersi:oCnofnrvoemrts/taodaecFimraalcotiroimnproper fraction to a  
How to Simplify a Fraction  
Reducing to its simplest form  
If the result of pressing = is displayed with the “SIMP”  
symbol, the calculation can be reduced further. Use the ª  
key to set the factor of the fraction to simplify, either automati-  
cally or manually.  
mixed fraction.  
æ : Converts a mixed fraction or decimal to an im-  
proper fraction. In some cases, a decimal may  
not be converted to a fraction.  
ø : Converts an improper fraction or a mixed frac-  
[Automatic Simplification]  
tion to a decimal.  
1
2
– + — = N 1 Ø 3 + 2 Ø 12 =  
SIMP 6/12  
5
3
12  
4– =  
N 4 5 Ø 6 =  
4¬5/6  
4.833333333  
29/6  
ªFACTOR? SIMP 6/12  
6
SIMP 6/12  
1/2  
[A.xxx]  
[A/B]  
ø
=*6_  
æ
=
1 ÷ 3 =  
[A/B]  
1 / 3 =  
0.333333333  
1/3  
*
If you do not know a common factor, press =. The  
æ
greatest common factor “6” will be displayed.  
[Manual Simplification]  
6 ÷ 5 =  
[A/B]  
B
[A / ]  
C
[A.xxx]  
2
1.25 + – =  
5
B
[A / ]  
C
6 / 5 =  
1.2  
12/10  
SIMP  
æ
1
3
2
12  
– + — = N 1 Ø 3 + 2 Ø 12 =  
SIMP 6/12  
SIMP  
º
1¬2/10  
ªFACTOR? SIMP 6/12  
ø
1.2  
2 =*  
SIMP 23/6  
1/2  
1.25 + 2 Ø 5 =  
1.65  
ª 3 =  
SIMP  
º
1¬65/100  
*
“2” is entered as a factor, and “SIMP” will be displayed  
to indicate further simplification of the fraction is possible.  
If the entered value is not a common factor, the cursor will  
be set under the value. Press d to clear the value, then  
enter a correct common factor. Press N to return to the  
“FACTOR?” display.  
ª==  
1¬13/20  
STATISTICAL CALCULATIONS  
Now that you have learned how to reduce a fraction to its  
simplest form, you can start using your calculator to per-  
form fraction calculations quickly and efficiently.  
To enter the statistical mode, press @”. The indicator  
symbol will appear. The following statistics can be  
obtained:  
5
6
1
14  
– + — = N 5 Ø 6 + 1 Ø 14 =  
SIMP 38/42  
19/21  
x
: Mean of sample (x)  
=*  
sx : Standard deviation of sample (x)  
σx : Population standard deviation of sample (x)  
*
If = is pressed instead of ª, the number will auto-  
matically be reduced down to its simplest form with the  
greatest common factor.  
n
: Number of samples  
Σx : Total number of samples (x)  
Σx2: Sum of the squares of sample (x)  
Reducing to the lowest denominator  
Entering Data  
Prior to pressing the = key, a common denominator can  
To enter sample data, use the numeric keys and press  
k(O key) after each value.  
be set to organize calculations.  
To enter data with its frequency, use the numeric keys to  
enter the value, then press §(R key), enter the fre-  
quency, then press k.  
1
1
– + – =  
N 1 Ø 3 + 1 Ø 4  
1/3+1/4_  
3
4
ªDENOM.? SIMP 28/48  
48 =*  
16/48+12/48_  
SIMP 28/48  
=
 
ERROR AND CALCULATION RANGES  
Enter the data “7” N@”  
7_  
1.*  
@c 7  
Errors  
k
n =  
An error will occur if an operation exceeds the calculation  
ranges, or if a mathematically illegal operation is attempted. If  
an error occurs, pressing < (or >) automatically moves  
the cursor back to the place in the equation where the error  
occurred. Edit the equation or press N to clear the  
equation.  
There are 13 students @c 70 § 13  
70, 13_  
13.  
50, 5_  
18.  
who scored 70 in the  
k
n =  
n =  
test, and 5 students 50 § 5  
who scored 50.  
k
*
The number of samples for the entered data will be dis-  
played.  
Entered data are kept in memory until @c or  
@” are pressed. Before entering new data, clear  
the memory contents.  
Error Codes and Error Types  
Syntax error (Error 1):  
An attempt was made to perform an invalid operation.  
Ex. 2 +- 5 =  
Calculation error (Error 2):  
If the number of the sample values exceeds 999,999,999  
n=” will not appear.  
When inputting a formula as a sample value with frequency,  
parenthesize the data.  
The absolute value of an intermediate or final calculation result  
equals or exceeds 10100  
.
An attempt was made to divide by 0.  
The calculation ranges were exceeded while performing calcu-  
lations.  
Example: ( A * B frequency k  
Correcting Entered Data  
Correction prior to pressing k:  
Delete incorrect data with N.  
Depth error (Error 3):  
The available number of buffers was exceeded. (There are 8  
buffers* for numeric values and 16 buffers for calculation in-  
structions).  
Correction after pressing k:  
press > to confirm the latest entry and press @J  
to delete it.  
* 4 buffers in STAT mode.  
Equation too long (Error 4):  
The equation exceeded its maximum input buffer (159 charac-  
ters). An equation must be shorter than 159 characters.  
Calculating Statistical Quantities  
@c  
5.  
Score Number of  
Persons  
30 § 5 k  
40 § 3 k  
50 § 10 k  
60 § 12 k  
70 § 13 k  
80 § 9 k  
90 § 7 k  
100 § 3 k  
@÷  
n =  
n =  
n =  
n =  
n =  
n =  
n =  
n =  
Calculation Ranges  
8.  
30  
40  
50  
60  
70  
80  
90  
100  
5
3
10  
12  
13  
9
Within the ranges specified below, this calculator is  
accurate to 1 of the least significant digit of the  
mantissa. However, a calculation error increases in con-  
tinuous calculations due to accumulation of each cal-  
18.  
30.  
43.  
52.  
59.  
62.  
culation error. (This is the same for yx, ¿y, etc. where  
x
continuous calculations are performed internally.)  
Additionally, a calculation error will accumulate and  
become larger in the vicinity of inflection points and  
singular points of functions.  
7
3
65.32258065  
18.52935128  
18.37931358  
@£  
Calculation range: 10-99  
~
9.999999999×1099 and 0.  
@p  
@n  
n =  
62.  
4050.  
285500.  
If the absolute value of an entry or a final or intermediate  
result of a calculation is less than 10–99, the value is consid-  
ered to be 0 in calculations and in the display.  
@z  
Σx =  
2
@w  
Σx  
=
Function  
Dynamic range  
If both the resulting digits and the function name (such as  
Σx=) cannot be contained in the display, only the resulting  
value will be displayed; the function name will not be  
displayed.  
sin x  
cos x  
tan x  
DEG : |x| < 1010  
(tan x : |x| 90(2n–1))*  
sin–1x  
Statistical Calculation Formulas  
|x| 1  
|x| < 10100  
cos–1x  
Σx  
tan–1x  
Σx2 – nx2  
x =  
n
σx =  
y > 0: –10100 < xlogy < 100  
.
n
x
y
. y = 0: 0 < x < 10100  
1
Σx2 – nx2  
n – 1  
1
2
Σx = x + x + ··· + x  
n
.
y < 0: x = n (0 < |x| < 1: – = 2n–1, x 0)*,  
x
Σx2 = x 2 + x 2 + ··· + x  
2
sx =  
1
2
n
–10100 < xlog |y| < 100  
(n: number of samples)  
1
y > 0: –10100 < – logy 100 (x 0)  
y = 0: 0 < x < 10  
.
.
.
x
100  
In the statistical calculation formulas, an error will occur if:  
x
¿y  
1
the absolute value of the intermediate result or calculation  
y < 0: x = 2n–1 (0 < |x| < 1: – = n, x 0)*,  
x
result is equal to or greater than 1 x 10100  
the denominator is zero.  
.
1
–10100 < – log |y| 100  
x
an attempt is made to take the square root of a negative  
number.  
 
x2  
x3  
|x| < 1050  
Automatic Power Off Function  
This calculator will turn its power off automatically if no key is  
pressed for about 10 minutes.  
|x| < 2.15443469  
0 x < 10100  
|x| < 10100 (x 0)  
×
1033  
¿x  
x–1  
* n: positive integers  
SPECIFICATIONS  
Calculations:  
General arithmetic operations (add,  
subtract, multiply, divide, operations  
with constants, memory operations,  
fraction operations, function  
BATTERY REPLACEMENT  
Notes on Battery Replacement  
Improper handling of batteries can cause electrolyte leakage  
or explosion. Be sure to observe the following handling rules:  
operations, statistical operations, etc.)  
Internal calculations: Mantissas of up to 12 digits  
Replace both batteries at the same time.  
Do not mix new and old batteries.  
Make sure the new batteries are the correct type.  
When installing, orient each battery correctly as indicated in  
the calculator.  
The factory-installed batteries may be exhausted before  
they reach the service life stated in the specifications.  
Pending operations:  
16 calculations 8 numeric values  
(4 numeric values in STAT mode)  
Power source:  
3 V (DC):  
Alkaline batteries (LR44) × 2  
Power consumption: 0.0006 W  
Operating time: Approx. 2000 hours, when continu-  
ously displaying 55555. at 25°C  
(77°F).  
When to Replace the Batteries  
If the display has poor contrast or nothing appears on the  
display even when N is pressed, it is time to replace the  
batteries.  
May vary according to usage and  
other factors.  
Operating temperature: 0°C – 40°C (32°F – 104°F)  
External dimensions: 78.6mm (W)× 144 mm (D)× 10.5mm (H)  
3-3/32” (W) × 5-21/32” (D) × 13/32” (H)  
Cautions  
Weight:  
Approx. 68 g (0.15 lb)  
(Including batteries)  
Batteries × 2 (installed), operation  
manual, quick reference card and  
hard case.  
Fluid from a leaking battery accidentally entering an eye  
could result in serious injury. Should this occur, wash with  
clean water and immediately consult a doctor.  
Should fluid from a leaking battery come into contact with  
your skin or clothes, immediately wash with clean water.  
If the product is not to be used for some time, to avoid  
damage to the unit from leaking batteries, remove them and  
store in a safe place.  
Accessories:  
FOR MORE INFORMATION ABOUT  
SCIENTIFIC CALCULATOR  
Do not leave exhausted batteries inside the product.  
Do not fit partially used batteries, and be sure not to mix  
batteries of different types.  
Visit us on the Internet at: http://sharp-world.com/calculator/  
Keep batteries out of the reach of children.  
Exhausted batteries left in the calculator may leak and  
damage the calculator.  
This equipment complies with the requirements of Directive 89/336/EEC as  
amended by 93/68/EEC.  
Dieses Gerät entspricht den Anforderungen der EG-Richtlinie 89/336/EWG mit  
Änderung 93/68/EWG.  
Explosion risk may be caused by incorrect handling.  
Do not throw batteries into a fire as they may explode.  
Ce matériel répond aux exigences contenues dans la directive 89/336/CEE modifiée  
par la directive 93/68/CEE.  
Dit apparaat voldoet aan de eisen van de richtlijn 89/336/EEG, gewijzigd door 93/68/  
EEG.  
Dette udstyr overholder kravene i direktiv nr. 89/336/EEC med tillæg nr. 93/68/EEC.  
Quest’apparecchio è conforme ai requisiti della direttiva 89/336/EEC come  
emendata dalla direttiva 93/68/EEC.  
Replacement Procedure  
1. Turn the power off by pressing @F.  
2. Loosen both screws and remove the bat-  
tery cover.  
ÂÁηٿÛÙ·ÛË ·˘Ù‹ ·ÓÙ·ÔÎÚ›ÓÂÙ·È ÛÙȘ ··ÈÙ‹ÛÂȘ ÙˆÓ Ô‰ËÁÈÒÓ Ù˘  
˘Úˆ·˚΋˜ ÓˆÛ˘ 89/336/∂√∫, ˆ˜ Ô Î·ÓÔÓÈÛ̘ ·˘Ù˜ Û˘ÌÏËÚÒıËΠ·fi  
ÙËÓ Ô‰ËÁ›· 93/68/∂√∫.  
Este equipamento obedece às exigências da directiva 89/336/CEE na sua versão  
corrigida pela directiva 93/68/CEE.  
3. Replace the old batteries with new, with  
the positive (+) sides facing up.  
Este aparato satisface las exigencias de la Directiva 89/336/CEE, modificada por  
medio de la 93/68/CEE.  
Denna utrustning uppfyller kraven enligt riktlinjen 89/336/EEC så som kompletteras  
av 93/68/EEC.  
4. Replace the battery cover and screws.  
5. Press the RESET switch on the back.  
Dette produktet oppfyller betingelsene i direktivet 89/336/EEC i endringen 93/68/  
EEC.  
Tämä laite täyttää direktiivin 89/336/EEC vaatimukset, jota on muutettu direktiivillä  
93/68/EEC.  
Make sure that the display appears  
as shown. Otherwise, remove the bat-  
teries, reinstall, and check the dis-  
play again.  
SHARP CORPORATION  
 

Shiro Telephone SB2112 User Manual
Sierra Monitor Corporation Carbon Monoxide Alarm Gas Sensor User Manual
Sony Car Stereo System XR M550 User Manual
Sony CRT Television KDL 32R500C User Manual
Sony Headphones CPF IP001 User Manual
Sony Microphone CU E672 User Manual
Sony Speaker System SHAKE55 User Manual
Stiga Lawn Mower DIESEL 4WD User Manual
Summit Mobility Aid HP 1 User Manual
Sunbeam Food Processor SM6200 User Manual