Sony Cassette Player TC SD1 User Manual

3-864-773-11(1)  
St e re o Ca sse t t e  
De ck  
Operating Instructions  
TC-SD1  
©1998 by Sony Corporation  
 
Th e TC-SD1 t a p e d e ck is  
d e sig n e d o n ly fo r t h e  
CMT-SD1/SD3 a n d  
MDS-SD1 co m p o n e n t  
syst e m  
Ta b le o f Co n t e n t s  
Ge t t in g St a rt e d  
Hooking up the system ......................... 4  
Here are some of the features you can use  
with this tape deck when connected with the  
CMT-SD1/ SD3 compact Hi-Fi component  
system (see page 4).  
Op e ra t io n s  
Playing a tape .......................................... 6  
Recording a CD ...................................... 8  
Recording manually ............................... 9  
Timer recording radio programmes .. 11  
The MDS-SD1 is also available (see page 4).  
Refer to “Recording manually” (page 9) to  
record from an MD to a tape, and refer to  
“Recording on an MD manually” (in the  
MDS-SD1 Operating Instructions) to record  
from a tape to an MD.  
Ad d it io n a l In fo rm a t io n  
Au t o Po w e r On /Off  
The tape deck power is tied with the  
CMT-SD1/ SD3 component system (see page  
6).  
Precautions ............................................ 13  
Troubleshooting ................................... 15  
Specifications ......................... Back cover  
CD Syn ch ro Re co rd in g  
You can easily record a CD onto a tape (see  
page 8).  
Au t o m a t ic So u rce Se le ct io n  
You can switch from another source to the  
tape deck and start playing a tape just by  
pressing · or ª on the tape deck (see page  
7).  
Tim e r  
You can wake up to music or record a radio  
programme at a preset time. For details, refer  
to “Falling asleep to music” and “Waking up  
to music” in the CMT-SD1/ SD3 component  
system Operating Instructions, and “Timer  
recording radio programmes” on page 11.  
Re m o t e Co n t ro l  
You can operate the tape deck using the  
remote supplied with the CMT-SD1/ SD3.  
3
 
Ho o kin g u p t h e syst e m  
Complete steps 1 through 3 (1 through 4 for CMT-SD3) to hook up your system using the  
supplied cords.  
The front panel is made of tempered glass. Please remember to handle this unit carefully.  
TC-SD1  
3(CMT-SD3 only)  
2
1
CMT-SD1/SD3  
4
5
Fo r t h e cu st o m e rs u sin g t h e MDS-SD1 a lre a d y  
Hook up your system as follows. To hook up the MDS-SD1 with CMT-SD1/ SD3, refer to the  
MDS-SD1 Operating Instructions.  
TC-SD1  
3(CMT-SD3 only)  
2
1
MDS-SD1  
4
CMT-SD1/SD3  
5
4
 
CThe sound signals of the CD, MD  
and TUNER flow through the  
CMT-SD1/ SD3 (and MDS-SD1) to the  
tape deck when you record onto a  
tape.  
1 Firmly connect the system cable to  
the SYSTEM CONTROL jack on the  
CMT-SD1/ SD3.  
When using the MDS-SD1, connect to  
the SYSTEM CONTROL jack on the  
MDS-SD1.  
D
The sound signal of the tape deck  
flows to the CMT-SD1/ SD3 when you  
play a tape.  
Ho w t o in se rt t h e p lu g s  
Insert the plugs firmly into the jacks.  
SYSTEM  
CONTROL  
Not firmly inserted.  
Insert to here.  
SYSTEM  
CONTROL  
3 For CMT-SD3, reconnect the Mains  
lead of the super woofer to the  
unswitched AC OUTLET on the  
TC-SD1.  
4 Connect the Mains lead of the  
TC- SD1 to the AC OUTLET on the  
CMT-SD1/ SD3.  
No t e  
The system cable is used for exchanging signals  
between the tape deck and the CMT-SD1/ SD3 (or  
MDS-SD1). If you do not connect the cord firmly,  
the tape deck may not operate correctly.  
When using the MDS-SD1, connect to  
the AC OUTLET on the MDS-SD1.  
5 Connect the Mains lead of the  
CMT-SD1/ SD3 to a mains after you  
complete all the connections.  
2 Connect C to C, and  
D
to  
D
using the audio connecting cords.  
Insert the plugs into jacks of the  
same colour.  
TC-SD1  
If t h e re is n o so u n d o r t h e t a p e  
d o e s n o t re co rd a t t h e first  
o p e ra t io n  
Make sure the plugs are inserted into the  
jacks firmly.  
D
D
If the plugs are not inserted into the C jacks  
firmly, you may not be able to record the sound  
of the CD, MD and TUNER onto a tape.  
D
If the plugs are not inserted into the  
C
jacks firmly, you may not be able to listen  
to the sound of the tape deck.  
The plugs of the audio connecting cords may  
be tight. Insert the plugs at the point shown  
in “How to insert the plugs” in step 2.  
CMT-SD1/SD3  
: signal flow  
5
 
1
2
Press 1/ u on the CMT-SD1/ SD3 to  
turn on the CMT-SD1/ SD3  
component system.  
Pla yin g a t a p e  
You can use any type of tape, TYPE I  
(normal), TYPE II (CrO2) or TYPE IV (metal),  
since the tape deck automatically detects the  
tape type (ATS1)).  
The tape deck turns on automatically.  
Press § on the tape deck to open the  
cassette tray and insert a recorded  
tape.  
1) ATS: Automatic Tape Selection.  
Tape deck  
TAPE  
TC-SD1  
Press § again to close the cassette tray.  
indicator  
1/u  
2
With the side you want  
to play facing up  
DOLBY NR2)  
∏ π 0/)  
3
ª 4  
3
4
Set DIRECTION to A to play one  
side, Å to play both sides once,  
and a3) to play both sides  
continuously.  
The remote supplied  
with the CMT-SD1/SD3  
Press ·.  
Press ª to play the bottom side.  
TAPE(  
0/)  
The function switches to “TAPE”  
automatically, then the tape starts  
playing.  
FUNCTION  
VOL  
3)  
The tape deck stops automatically after repeating  
the sequence five times.  
2)  
This tape deck is able to switch between Dolby B-  
type and C-type noise reduction systems.  
To p la y a t a p e u sin g t h e  
CMT-SD1/SD3 co m p o n e n t syst e m  
Do the following operations in step 4;  
1 Press FUNCTION until “TAPE” appears in  
the display.  
2 Press TAPE( on the remote.  
To play the bottom side, press TAPE(  
again on the remote.  
6
 
Tip s  
Ot h e r o p e ra t io n s  
• When you press 1/ u on the tape deck while the  
CMT-SD1/ SD3 is power on, only the tape deck  
turns on/ off. Press 1/ u on the CMT-SD1/ SD3 to  
turn on the CMT-SD1/ SD3 component system.  
• The TAPE indicator lights up in red when a  
cassette is inserted and goes off when no cassette  
is inserted.  
• You can switch from another source to the tape  
deck just by pressing · or ª (Automatic  
Source Selection).  
To  
Press  
Stop playing  
Pause  
π (or p*).  
(or P*).  
Press again to resume playing.  
Fast-forward  
π, then ) (or )*) for the  
top side.  
π, then 0 (or 0*) for the  
bottom side.  
Rewind  
π, then 0 (or 0*) for the  
top side.  
π, then ) (or )*) for the  
bottom side.  
• To start playing automatically from the beginning  
of the tape after fast winding (Auto Play), press  
· while holding down 0 (for the top side) or  
press ª while holding down ) (for the bottom  
side).  
Find the  
succeeding  
track (AMS**) side.  
) (or )*) for the top side.  
0 (or 0*) for the bottom  
• When listening to tapes recorded in Dolby NR, set  
DOLBY NR to “Bor “C”.  
• Using the timer function on the CMT-SD1/ SD3,  
you can wake up to music at a preset time. For  
details, refer to “Wake up to music” in the  
CMT-SD1/ SD3 component system Operating  
Instructions. When you set the Wake-up timer,  
DOLBY NR must be set on the tape deck.  
Find the  
0 (or 0*) for the top side.  
preceding track ) (or )*) for the bottom  
(AMS**)  
side.  
Remove the  
cassette  
§ on the tape deck.  
No t e  
Adjust the  
volume  
Turn VOLUME on the  
CMT-SD1/ SD3 (or VOL  
*).  
The AMS feature may not work in the following  
cases:  
/
— the blank space between tracks is four seconds  
or less.  
* Use the remote supplied with the CMT-SD1/ SD3.  
**The Automatic Music Sensor (AMS) feature  
detects a blank space of more than four seconds  
between tracks to locate tracks quickly.  
— the sound source recorded on the right  
channel is different from that on the left  
channel as with a KARAOKE tape.  
— low volume or low sound continues for a long  
time.  
— the TV is too close to the tape deck.  
7
 
2
Press § on the tape deck to open the  
cassette tray and insert a blank tape.  
Press § again to close the cassette tray.  
Re co rd in g a CD  
— CD Syn ch ro Re co rd in g  
With the side you want to  
record on facing up  
The CD SYNC button lets you record from a  
CD to a tape easily. You can use TYPE I  
(normal), TYPE II (CrO2), or TYPE IV (metal)  
tape, since the tape deck automatically  
detects the tape type.  
Tape deck  
TAPE  
TC-SD1  
1/u indicator  
2
3
4
Place a CD on the disc tray of the  
CMT-SD1/ SD3.  
Set DIRECTION to A to record on  
one side, Å to record on both  
sides once.  
DOLBY NR*  
ª
4 6  
7 π  
5
5
Press REC LEVEL lightly to release,  
and turn to set the recording level.  
REC LEVEL position around 4 sets the  
general recording level for most CDs.  
The remote supplied  
with the CMT-SD1/SD3  
To set a specific recording level for the  
CD you are recording, see "Recording  
Manually" on page 9.  
p
6
Press CD SYNC on the tape deck.  
The tape deck stands by for recording  
and the CMT-SD1/ SD3 stands by for  
playback. The indicators on the CD  
SYNC, rREC, · (for the top side) and  
buttons light up.  
If you want to record starting from the  
bottom side, press ª (for the bottom  
side) so the indicator on the ª button  
lights up.  
* This tape deck is able to switch between Dolby B-  
type and C-type noise reduction systems.  
1
Press 1/ u on the CMT-SD1/ SD3 to  
turn on the CMT-SD1/ SD3  
component system.  
The tape deck turns on automatically.  
8
 
7
Press on the tape deck.  
Recording starts.  
Re co rd in g m a n u a lly  
With manual recording, you can record just  
the songs you like from a CD, or start  
recording from the middle of the tape. You  
can also record a radio programme or MD.  
To st o p re co rd in g  
Press π on the tape deck or p on the remote.  
Tip s  
Tape deck  
TC-SD1 1/u indicator  
TAPE  
• When you press 1/ u on the tape deck while the  
CMT-SD1/ SD3 is power on, only the tape deck  
turns on/ off. Press 1/ u on the CMT-SD1/ SD3 to  
turn on the CMT-SD1/ SD3 component system.  
• The TAPE indicator lights up in red when a  
cassette is inserted and goes off when no cassette  
is inserted.  
2
• When you want to reduce the hiss noise in low-  
level high-frequency signals, set DOLBY NR to  
Bor “C” before step 5. Switching DOLBY NR  
while recording will cause the newly recorded  
sound to differ in quality from the previously  
recorded sound.  
• If the tape reaches the end of the top side during  
both sides recording, the fadeout feature prevents  
the track from ending abruptly at the end of the  
tape (Fade Synchro). The track is recorded again  
from the beginning of the bottom side.  
DOLBY NR*  
ª
·9 π  
4 5  
7
The remote supplied with  
the CMT-SD1/SD3  
• The fadeout feature also works when you record  
on one side only.  
p
• When you want to record onto both tape and MD  
at one time, use CD synchro recording on the tape  
deck, and manual recording on the MD. You  
cannot use CD synchro recording on both units  
simultaneously. This tape deck's fadeout feature  
(Fade Synchro) will cause a track to be recorded  
twice on the MD. After recording is completed,  
use the MD's editing functions to erase this extra  
track.  
3
No t e s  
• You cannot listen to other sources while recording.  
• When you record on both sides, be sure to start  
from the top side. If you start from the bottom  
side, recording stops at the end of the bottom side.  
* This tape deck is able to switch between Dolby B-  
type and C-type noise reduction systems.  
1
Press 1/ u on the CMT-SD1/ SD3 to  
turn on the CMT-SD1/ SD3  
component system.  
The tape deck turns on automatically.  
continued  
9
 
Re co rd in g m a n u a lly (co n t in u e d )  
6
7
Start playback on the component  
you want to record.  
2
Press § on the tape deck to open the  
cassette tray and insert a blank tape.  
Press § again to close the cassette tray.  
Press REC LEVEL lightly to release,  
and turn to set the recording level.  
The level indicator reads the current  
recording level.  
With the side you want  
to record on facing up  
Adjust as the 0 (zero) indicator lights up  
dB  
+6  
+3  
a
0
-
-10  
-5  
8
9
Once you have set the recording  
level, stop playback on the source  
component.  
3
Press FUNCTION on the  
CMT-SD1/ SD3 until the source you  
want to record (such as “TUNER”  
or “AUX*) appears in the display.  
Press on the tape deck.  
Recording starts.  
When recording from CD or MD, select  
the track you wish to record and pause  
playback.  
10Start playing on the source  
component.  
When recording off the radio, tune in the  
preset station.  
* Select to record the audio output of the  
component connected to the CMT-SD1/ SD3  
AUX jacks.  
For details, refer to "Optional A/ V  
components" in the CMT-SD1/ SD3 component  
system Operating Instructions.  
To  
Press  
Stop recording  
Pause recording  
π (or p on the remote)  
(or P on the remote)  
4
5
Set DIRECTION to A to record on  
one side, Å to record on both  
sides once.  
Press rREC on the tape deck.  
The tape deck stands by for recording.  
The indicators on the rREC and · (for  
the top side) buttons light up.  
If you want to record starting from the  
bottom side, press ª (for the bottom  
side) so the indicator on the ª button  
lights up.  
10  
 
Tip s  
• The TAPE indicator lights up in red when a  
cassette is inserted and goes off when no cassette  
is inserted.  
• When you want to reduce the hiss noise in low-  
level high-frequency signals, set DOLBY NR to  
Bor “C” before step 5. Switching DOLBY NR  
while recording will cause the newly recorded  
sound to differ in quality from the previously  
recorded sound.  
Tim e r re co rd in g  
ra d io p ro g ra m m e s  
To timer record, you must first preset the  
radio station and set the clock on the  
CMT-SD1/ SD3 (refer to the CMT-SD1/ SD3  
component system Operating Instructions).  
• Using the timer function on the CMT-SD1/ SD3,  
you can record radio programmes at a preset time.  
For details, refer to “Timer recording radio  
programmes” on this page. When you set the  
timer recording, DOLBY NR, REC LEVEL and  
DIRECTION mode must be set on the tape deck.  
The remote supplied  
with the CMT-SD1/SD3  
8
2
TIMER SELECT  
3~6  
3~6  
1
Tune in the preset radio station  
(refer to the CMT-SD1/ SD3  
component system Operating  
Instructions).  
2
3
Press TIMER SET.  
Press +/ – repeatedly until “REC  
TIMER?” appears, then press  
ENTER.  
The hour indication flashes.  
continued  
11  
 
Tim e r re co rd in g ra d io p ro g ra m m e s  
(co n t in u e d )  
7
Press § on the tape deck to open the  
cassette tray and insert a blank tape.  
Press § again to close the cassette tray.  
4
Set the time to start recording.  
Press +/ – to set the hour, then press  
ENTER.  
With the side you want to  
record on facing up  
The minute indication flashes.  
SHUFFLE PROGRAM REPEAT  
1
TUNED STEREO MONO  
SURR  
DBFB  
DAILY REC SLEEP  
DISC  
AUTO  
kHz  
MHz  
MANUAL PREST  
Press +/ – to set the minute, then press  
ENTER.  
The hour indication flashes again.  
8
Press 1/ u on the CMT-SD1/ SD3 to  
turn off the system.  
The tape deck is now ready for the timer  
recording. The power turns on  
automatically at the start time, the  
recorging starts, then the power turns off  
at the stop time.  
5
6
Set the time to stop recording  
following the procedure in step 4.  
If the stop time is same as the start time,  
“OFF TIME NG!appears and the  
display returns to set the stop time. Set  
the time to stop recording again.  
Press +/ – repeatedly until “TUNER  
to TAPE” appears, then press  
ENTER.  
The start time appears, followed by the  
stop time, preset number and “TAPE”,  
then the original display appears.  
“REC” in the display and the timer  
indicator light up.  
Wh e n “ CONNECTION” a p p e a rs  
The system cable is not connected correctly.  
Turn off the power, connect the components  
correctly, and turn on the power again. Then  
start over from step 1.  
12  
 
To ca n ce l t im e r re co rd in g  
Press TIMER SET.  
Pre ca u t io n s  
To ch a n g e t h e se t t in g  
Start again from step 1.  
Ab o u t t e m p e re d g la ss  
The front panel of this tape deck is made of  
tempered glass, which has been known to break in  
extreme circumstances.  
To ch e ck t h e se t t in g / To u se t h e  
t im e r  
Press TIMER SELECT repeatedly until “REC”  
appears. The start time appears, followed by  
the stop time, the preset number, and  
“TAPE”, then the original display appears.  
Press 1/u on the CMT-SD1/ SD3 to turn off  
the system. The tape deck stands by for the  
timer recording.  
On sa fe t y  
• The unit is not disconnected from the AC power  
source (mains) as long as it is connected to the  
wall outlet, even if the unit itself has been turned  
off.  
• Unplug the tape deck from the wall outlet (mains)  
if it is not to be used for an extended period of  
time. To disconnect the cord (mains lead), pull it  
out by the plug. Never pull the cord itself.  
• Should any solid object or liquid fall into the  
component, unplug the tape deck and have it  
checked by qualified personnel before operating it  
any further.  
To ca n ce l t h e t im e r  
Press TIMER SELECT repeatedly until  
“TIMER OFF” appears.  
Tip s  
• The AC power cord (mains lead) must be changed  
only at a qualified service shop.  
• This tape deck is able to switch between Dolby B-  
type and C-type noise reduction systems.  
• The last settings are memorized. To activate  
recording timer with the same settings, display  
“REC” and turn off the power. It is not necessary  
to set every time.  
On p la ce m e n t  
• Place the tape deck in a location with adequate  
ventilation to prevent heat build-up in the tape  
deck.  
• Do not place the unit in an inclined position.  
• Do not place the unit in locations where it is:  
— Extremely hot or cold  
— Dusty or dirty  
— Very humid  
— Subject to vibration  
— Subject to direct sunlight.  
No t e s  
• You cannot activate wake up timer and recording  
timer at the same time.  
• Do not operate the system from the time the  
power turns on until the playback starts (about 20  
seconds).  
• If the power is on about 20 seconds before the  
preset time, the recording will not be made.  
• The volume is reduced to minimum during  
recording.  
Be fo re p la cin g a ca sse t t e in t h e  
t a p e d e ck  
Take up any slack in the tape. Otherwise, the tape  
may get entangled in the parts of the tape deck and  
become damaged.  
Wh e n u sin g a t a p e lo n g e r t h a n 90  
m in u t e s  
The tape is very elastic. Do not change the tape  
operations such as play, stop, and fast-winding  
frequently. The tape may get entangled in the tape  
deck.  
continued  
13  
 
Pre ca u t io n s (co n t in u e d )  
Cle a n in g t h e t a p e h e a d s  
Clean the tape heads after every 10 hours of use.  
When the tape heads become dirty  
— the sound is distorted  
To sa ve a t a p e p e rm a n e n t ly  
— there is a decrease in sound level  
— the sound drops out  
— the tape does not erase completely  
— the tape does not record.  
To prevent a tape from being accidentally recorded  
over, break off the cassette tab from side A or B as  
illustrated.  
Be sure to clean the tape heads before you start an  
important recording or after playing an old tape.  
Use a separately sold dry-type or wet-type cleaning  
cassette. For details, refer to the instructions of the  
cleaning cassette.  
Detector slots  
De m a g n e t isin g t h e t a p e h e a d s  
Demagnetise the tape heads and the metal parts  
that has contact with the tape after every 20 to 30  
hours of use with a separately sold demagnetising  
cassette. For details, refer to the instructions of the  
demagnetising cassette.  
Tab of side B  
Tab of side A  
Side A  
Break off the  
cassette tab  
of side A  
Cle a n in g t h e ca b in e t  
Use a soft cloth slightly moistened with mild  
detergent solution.  
Never use strong solvents, such as thinner or  
benzene, since they may damage the finish.  
If you later want to reuse the tape for recording,  
cover the broken tab with adhesive tape. However,  
be careful not to cover the detector slots which allow  
the tape player to automatically detect the type of  
tape.  
If you have any questions or problems concerning  
your tape deck, please consult your nearest Sony  
dealer.  
Tape type:  
CrO2/METAL  
NORMAL  
Detector slots  
14  
 
Noise increases or the high frequencies are  
erased.  
• The record/ playback heads are  
magnetised. Demagnetise them (see page  
14).  
Tro u b le sh o o t in g  
If you run into any problem using this tape  
deck, use the following checklist.  
• Move the tape deck away from the TV or  
VCR.  
First, check that the mains lead is connected  
firmly and the speakers are connected  
correctly and firmly.  
The sound is distorted.  
• Set DOLBY NR to the same setting in  
which the tape was recorded.  
• Move the tape deck away from the TV or  
VCR.  
Should any problem persist, consult your  
nearest Sony dealer.  
There is no sound.  
The cassette tray does not close.  
• The mains lead is disconnected from the  
mains.  
• Make sure the audio connecting cords are  
connected correctly (see page 5). Make  
sure the plugs have been inserted firmly.  
• Turn on the power again, and close the  
cassette tray.  
The operation buttons on the tape deck do  
not w ork.  
• Press any of the operation buttons after ∏  
stops flashing. (The buttons on the tape  
deck do not work for about two seconds  
after the tape deck turns on.)  
The remote supplied w ith the CMT-SD1/  
SD3 does not function.  
• Press FUNCTION on the CMT-SD1/ SD3  
repeatedly to switch the FUNCTION to  
“TAPE”.  
No cassette is inserted. Insert a cassette.  
The tape does not play or record.  
• There is slack in the tape. Take up any  
slack in the tape.  
• Make sure the system cable is connected  
correctly (see page 5).  
• The operation buttons being used are  
located on the cover of the remote control  
and the cover is not completely closed.  
Make sure that the cover of the remote  
control is completely closed.  
• The heads are dirty. Clean them.  
• Make sure the audio connecting cords are  
connected correctly (see page 5).  
Make sure the plugs have been inserted  
firmly.  
Automatic Source Selection does not w ork.  
The tape does not record.  
No cassette is inserted.  
• Make sure the system cable is connected  
correctly (see page 5).  
• The tab has been removed from the  
cassette. Cover the broken tab with  
adhesive tape (see page 14).  
The functions tied w ith the CMT-SD1/SD3,  
such as CD Synchro Recording, do not  
w ork.  
• Make sure the system cable is connected  
correctly (see page 5).  
• The tape has wound to the end.  
The tape does not record or play, or there  
is a decrease in sound level.  
• The heads are dirty. Clean them.  
• The record/ playback heads are  
magnetised. Demagnetise them.  
The inserted tape w ill not eject.  
1/u of the tape deck is OFF. Press 1/u to  
turn on the tape deck, then press §.  
The tape does not erase completely.  
• The record/ playback heads are  
magnetised. Demagnetise them.  
There is excessive w ow or flutter, or the  
sound drops out.  
• The capstans in the tape deck are dirty.  
Clean them using a cleaning cassette.  
15  
 
Sp e cifica t io n s  
Recording system  
4-track 2-channel stereo  
Frequency response  
(DOLBY NR OFF)  
30 – 14,000 Hz (±3 dB),  
using Sony TYPE I  
cassettes  
30 – 15,000 Hz (±3 dB),  
using Sony TYPE II  
cassettes  
30 – 15,000 Hz (±3 dB),  
using Sony TYPE IV  
cassettes  
Wow and flutter  
±0.13% W. Peak (IEC)  
0.07% W. RMS (NAB)  
±0.2% W. Peak (DIN)  
TAPE IN (phono jacks):  
impedance 47 kilohms  
TAPE OUT (phono jacks):  
voltage 500 mV  
Input  
Output  
impedance 47 kilohms  
Ge n e ra l  
Power requirements  
European countries model:  
220 – 230 V AC, 50/ 60 Hz  
220 – 240 V AC, 50/ 60 Hz  
12 W  
Approx. 190 × 91 × 315  
mm (w/ h/ d)  
Other models:  
Power consumption  
Dimensions  
incl. projecting parts and  
controls  
Mass  
Approx. 3.2 kg  
Supplied accessories:  
Audio connecting cords  
(2)  
System cable (1)  
Design and specifications are subject to change  
without notice.  
Sony Corporation Printed in China  
 

Shark Vacuum Cleaner EP600 User Manual
Sony Clock Radio ICF CD523 User Manual
Sony Computer Monitor SDM M81 User Manual
Sony MP3 Player D NE20 User Manual
Sony Portable Speaker SMS1P User Manual
Star Micronics Printer LS 5 EX User Manual
Sterling Plumbing Product 1086447 2 A User Manual
Stoelting Freezer F144I User Manual
Sylvania TV DVD Combo SSC509D User Manual
Tamron Camera Lens A031 User Manual