Sony DVD Player DVP SR200P B User Manual

4-115-660-11(1)  
CD/DVD  
Player  
US  
ES  
Operating Instructions  
Manual de instrucciones  
DVP-SR200P  
© 2008 Sony Corporation  
 
hour until the moisture  
evaporates.  
• When you move the player, take  
out any discs. If you don’t, the  
disc may be damaged.  
Notes about the discs  
On safety  
• To keep the disc clean, handle  
the disc by its edge. Do not touch  
the surface. Dust, fingerprints, or  
scratches on the disc may cause  
it to malfunction.  
• To prevent fire or shock hazard,  
do not place objects filled with  
liquids, such as vases, on the  
apparatus.  
• Should any solid object or liquid  
fall into the cabinet, unplug the  
player and have it checked by  
qualified personnel before  
operating it any further.  
For the model supplied  
with the AC plug adaptor  
If the AC plug of your unit does not  
fit into the wall outlet, attach the  
supplied AC plug adaptor.  
On power sources  
• The player is not disconnected  
from the AC power source as  
long as it is connected to the wall  
outlet, even if the player itself  
has been turned off.  
• If you are not going to use the  
player for a long time, be sure to  
disconnect the player from the  
wall outlet. To disconnect the  
AC power cord, grasp the plug  
itself; never pull the cord.  
On adjusting volume  
Do not turn up the volume while  
listening to a section with very low  
level inputs or no audio signals. If  
you do, the speakers may be  
damaged when a peak level section  
is played.  
• Do not expose the disc to direct  
sunlight or heat sources such as  
hot air ducts, or leave it in a car  
parked in direct sunlight as the  
temperature may rise  
considerably inside the car.  
• After playing, store the disc in its  
case.  
• Clean the disc with a cleaning  
cloth. Wipe the disc from the  
center out.  
On cleaning  
On placement  
US  
Clean the cabinet, panel, and  
• Place the player in a location  
with adequate ventilation to  
prevent heat build-up in the  
player.  
controls with a soft cloth slightly  
moistened with a mild detergent  
solution. Do not use any type of  
abrasive pad, scouring powder or  
solvent such as alcohol or benzine.  
• Do not place the player on a soft  
surface such as a rug.  
• Do not place the player in a  
location near heat sources, or in a  
place subject to direct sunlight,  
excessive dust, or mechanical  
shock.  
• Do not install the player in an  
inclined position. It is designed  
to be operated in a horizontal  
position only.  
• Keep the player and the discs  
away from equipment with  
strong magnets, such as  
microwave ovens, or large  
loudspeakers.  
On cleaning discs, disc/  
lens cleaners  
Do not use cleaning discs or  
disc/lens cleaners (including  
wet or spray types). These  
may cause the apparatus to  
malfunction.  
• Do not use solvents such as  
benzine, thinner, commercially  
available cleaners, or anti-static  
spray intended for vinyl LPs.  
• If you have printed the disc’s  
label, dry the label before  
playing.  
On replacement of parts  
In the event that this unit is  
repaired, repaired parts may be  
collected for reuse or recycling  
purposes.  
• Do not place heavy objects on  
the player.  
Precautions  
• Do not install this player in a  
confined space, such as a  
bookshelf or similar unit.  
• Install the player so that the AC  
power cord can be unplugged  
from the wall socket  
IMPORTANT NOTICE  
The power requirements and  
power consumption of this player  
are indicated on the back of the  
player. Check that the player’s  
operating voltage is identical with  
your local power supply.  
Caution: This player is capable  
of holding a still video image or  
on-screen display image on your  
television screen indefinitely. If  
you leave the still video image  
or on-screen display image  
displayed on your TV for an  
extended period of time you risk  
permanent damage to your  
television screen. Plasma  
immediately in the event of  
trouble.  
Power requirements and  
power consumption  
On operation  
• If the player is brought directly  
from a cold to a warm location,  
or is placed in a very damp room,  
moisture may condense on the  
lenses inside the player. Should  
this occur, the player may not  
operate properly. In this case,  
remove the disc and leave the  
player turned on for about half an  
m
display panel televisions and  
projection televisions are  
susceptible to this.  
DVP–XXXX  
X
00V 00Hz  
NO.  
00W  
0-000-000-00  
If you have any questions or  
problems concerning your player,  
please consult your nearest Sony  
dealer.  
3US  
 
     
Table of Contents  
A Audio/video input jacks. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9  
B Component video input jacks (Y, PB, PR) . . . . . . . . . . . . . . . . . . . . . . . 9  
Adjusting the playback picture (CUSTOM PICTURE MODE) . . . . . . . . . 22  
Sharpening the picture (SHARPNESS). . . . . . . . . . . . . . . . . . . . . . . . . . 22  
Locking discs (PARENTAL CONTROL) . . . . . . . . . . . . . . . . . . . . . . . . . 22  
4US  
 
Self-diagnosis Function (When letters/numbers appear on the screen) . . . . 34  
About This Manual  
• Instructions in this manual describe the controls on the remote. You can also use the controls  
on the player if they have the same or similar names as those on the remote.  
• “DVD” may be used as a general term for commercial DVDs, DVD+RWs/DVD+Rs/DVD+R  
DLs (+VR mode) and DVD-RWs/DVD-Rs/DVD-R DLs (VR mode, video mode).  
• NEED-to-know information (to prevent incorrect operation) is listed under the  
b
icon. NICE-  
to-know information (tips and other useful information) is listed under the  
• The meaning of the icons used in this manual is described below:  
z
icon.  
Icons  
Meaning  
Functions available for commercial DVDs and DVD+RWs/DVD+Rs/  
DVD+R DLs in +VR mode or DVD-RWs/DVD-Rs/DVD-R DLs in video  
mode  
Functions available for DVD-RWs/DVD-Rs/DVD-R DLs in VR (Video  
Recording) mode  
Functions available for VIDEO CDs (including Super VCDs or CD-Rs/  
CD-RWs in video CD format or Super VCD format)  
Functions available for music CDs or CD-Rs/CD-RWs in music CD format  
Functions available for DATA discs containing MP3* audio tracks and  
JPEG image files  
* MP3 (MPEG-1 Audio Layer III) is a standard format defined by ISO (International Organization for  
Standardization)/IEC (International Electrotechnical Commission) MPEG which compresses audio  
data.  
5US  
 
               
Guide to Parts and Controls  
For more information, see the pages indicated in parentheses.  
Remote  
TV [/1 (on/standby) (11)  
Turns the TV on or to standby mode.  
[/1 (on/standby) (12)  
Turns on, or sets the player to standby  
mode.  
VOL +/– (11)  
Adjusts the TV volume.  
B Number buttons  
Enters the title/chapter numbers, etc.  
CLEAR (17)  
Clears the entry field.  
C TIME/TEXT (23)  
Displays the playing time and  
remaining time. Press repeatedly to  
change the displayed information.  
CD/DVD text appears only when text  
is recorded on the disc.  
If an MP3 audio track has an ID3 tag,  
the player will display the album  
name/track title from the ID3 tag  
information. This player supports ID3  
versions 1.0/1.1 and 2.2/2.3.  
VOL +, number 5, AUDIO, and N buttons have a  
tactile dot. Use the tactile dot as a reference when  
operating the player.  
AUDIO (  
)
Changes the audio language or audio  
channel.  
A PICTURE NAVI (24)  
Divides the screen into 9 subscreens  
so you can choose the desired scene  
quickly.  
Each time you press the button, the  
display changes as follows:  
• CHAPTER VIEWER  
When 4 digits are displayed, they  
indicate a language code. See  
see which language the code  
represents.  
The format of the current audio signal  
(Dolby Digital, DTS, PCM, etc.)  
appears as shown on page 7.  
• TITLE VIEWER  
• TRACK VIEWER  
The JPEG image files in the album  
appear in 16 subscreens.  
TV INPUT (input select) (11)  
Switches the TV’s input source  
between the TV and other input  
sources.  
6US  
 
               
Basic operations  
When playing a DVD VIDEO  
Example:  
Dolby Digital 5.1 ch  
To  
Operation  
Press N.  
Press x.  
Play  
Stop  
Pause  
Rear (L/R)  
Press X.  
:
3 / 2 .1  
ENGLISH DOLBY DIGITAL  
1
Go to the next chapter, Press >.  
track, or scene in  
continuous play mode  
LFE (Low Frequency  
Effect)  
Front (L/R)  
+ Center  
Go back to the  
Press ..  
previous chapter,  
track, or scene in  
continuous play mode  
SUBTITLE ( ) (25)  
Changes the subtitles.  
D TOP MENU  
Scan backward/  
forward  
Press  
M
Press repeatedly to  
change the speed.  
m/  
.
Displays the DVD’s top menu.  
MENU (23)  
Displays the menu.  
Replay the previous  
scene* *  
Press  
REPLAY during  
playback.  
1
3
O RETURN (15)  
Returns to the previous display.  
Briefly fast forward  
Press  
ADVANCE during  
playback.  
2
3
DISPLAY (16)  
Displays the playback information on  
the current scene* *  
the screen.  
4
Play backward* /  
Press X during  
playback, then press  
m/M  
5
forward* in slow  
C/X/x/c (12)  
Moves the highlight to select a  
displayed item.  
motion  
repeatedly.  
4
Play backward* /  
Press X during  
5
forward* one frame playback, then press  
Center button (ENTER) (12)  
Enters the selected item.  
at a time  
/
.
Play in various speed Press FAST/SLOW  
E ./> PREV/NEXT  
6
with sound*  
PLAY repeatedly  
during playback.  
/
REPLAY/STEP/  
1
STEP/ADVANCE  
*
For all DVDs except for DVD+RWs/DVD+Rs/  
DVD+R DLs.  
For DVDs only.  
2
3
m/M  
N PLAY  
X PAUSE  
x STOP  
(scan/slow)  
*
*
These functions may not work with some  
scenes.  
4
5
6
*
*
*
For DVD VIDEOs and DVD-VR mode only.  
For DVDs and VIDEO CDs only.  
For DVDs, VIDEO CDs, Super VCDs and  
DVD-VR mode only.  
FAST/SLOW PLAY  
See “Basic operations” (page 7) for the  
function of each button.  
7US  
,continued  
 
                   
Front panel  
A [/1 (on/standby) button (12)  
E Z (open/close) button (14)  
F N (play) button (14)  
G x (stop) button (14)  
C Front panel display (15)  
D
(remote sensor) (10)  
Rear panel  
PB  
VIDEO  
L
DIGITAL  
OUT  
VIDEO OUT  
COMPONENT  
VIDEO OUT  
R
Y
PR  
COAXIAL  
AUDIO OUT  
A VIDEO OUT jack (9)  
B COMPONENT VIDEO OUT jacks (9)  
C DIGITAL OUT (COAXIAL) jack (10)  
D AUDIO OUT L/R jacks (9)  
8US  
 
Hookups  
When unpacking, check the supplied accessories by referring to page 36.  
b
• Plug cables securely to prevent unwanted noise.  
• Refer to the instructions supplied with the components to be connected.  
• Be sure to disconnect the power cord of each component before connecting.  
Step 1: Connecting to Your TV  
Connect this player to your TV monitor using a video cable. Select pattern A or B, according  
to the input jack on your TV monitor, projector, or audio component.  
INPUT  
(white)  
A
L
Audio/video cable (supplied)  
AUDIO  
(red)  
R
(yellow)  
VIDEO  
(red)  
(white)  
(yellow)  
TV  
to VIDEO OUT  
to AUDIO OUT  
P
B
VIDEO  
L
DIGITAL  
OUT  
VIDEO OUT  
COMPONENT  
VIDEO OUT  
R
Y
P
R
COAXIAL  
AUDIO OUT  
CD/DVD player  
to COMPONENT  
VIDEO OUT  
(green)  
(red)  
(blue)  
COMPONENT  
VIDEO IN  
B
Y
(green)  
Component video  
cable (not supplied)  
PB  
PR  
(blue)  
(red)  
TV  
: Signal flow  
When connecting to a wide screen TV  
Depending on the disc, the image may not fit  
your TV screen. To change the aspect ratio,  
see page 27.  
A Audio/video input jacks  
You will enjoy standard quality images.  
B Component video input jacks  
(Y, PB, PR  
)
b
You will enjoy accurate color reproduction  
and high quality images.  
Do not connect a VCR, etc., between your TV and  
the player. If you pass the player signals via the  
VCR, you may not receive a clear image on the TV  
screen. If your TV has only one audio/video input  
jack, connect the player to this jack.  
b
Connect the supplied audio cable to audio input  
jacks (L/R) on your TV.  
9US  
,continued  
 
           
To connect to your audio component  
Use the following pattern.  
Step 2: Connecting the  
Power Cord  
CD/DVD player  
PB  
VIDEO  
L
DIGITAL  
OUT  
VIDEO OUT  
COMPONENT  
VIDEO OUT  
R
Y
PR  
COAXIAL  
AUDIO OUT  
Plug the player and TV power cords into an  
AC outlet.  
to DIGITAL OUT  
(COAXIAL)  
DIGITAL  
OUT  
COAXIAL  
Step 3: Preparing the  
Remote  
Coaxial digital cable  
(not supplied)  
You can control the player using the supplied  
remote. Insert two Size AA (R6) batteries by  
matching the 3 and # ends on the batteries  
to the markings inside the compartment.  
When using the remote, point it at the remote  
to coaxial  
digital input  
Audio component  
with a decoder  
sensor  
on the player.  
: Signal flow  
z
For correct speaker location, see the operating  
instructions supplied with the connected  
components.  
1
If your audio component has a Dolby*  
2
Digital or DTS* decoder and a digital input  
jack, use this connection. You can enjoy  
Dolby Digital (5.1ch) and DTS (5.1ch)  
surround effect.  
b
• Do not leave the remote in an extremely hot or  
humid place.  
• Do not drop any foreign object into the remote  
casing, particularly when replacing the batteries.  
• Do not expose the remote sensor to direct light  
from the sun or a lighting apparatus. Doing so  
may cause a malfunction.  
• If you do not use the remote for an extended  
period of time, remove the batteries to avoid  
possible damage from battery leakage and  
corrosion.  
*1  
Manufactured under license from Dolby  
Laboratories.  
Dolby, Pro Logic, and the double-D symbol are  
trademarks of Dolby Laboratories.  
Manufactured under license under U.S. Patent #:  
*2  
5,451,942 & other U.S. and worldwide patents  
issued & pending. DTS and DTS Digital Out are  
registered trademarks and the DTS logos and  
Symbol are trademarks of DTS, Inc. © 1996-  
2007 DTS, Inc. All Rights Reserved.  
b
• After you have completed the connection, make  
the appropriate settings in Quick Setup (page 12).  
Otherwise, no sound or a loud noise will come  
from your speakers.  
• The TVS effects of this player cannot be used  
with this connection.  
• In order to listen to DTS sound tracks, you must  
use this connection. DTS sound tracks are not  
output through the AUDIO OUT L/R jacks, even  
if you set “DTS” to “ON” in Quick Setup  
10US  
 
           
To control other TVs with the remote  
You can control the sound level, input source,  
and power switch of non-Sony TVs as well.  
If your TV is listed in the table below, set the  
appropriate manufacturer’s code.  
Controlling your TV with the  
supplied remote  
You can control the sound level, input source,  
and power switch of your Sony TV with the  
supplied remote.  
1
While holding down TV [/1, press the  
number buttons to select your TV’s  
manufacturer’s code (see the table  
below).  
TV INPUT  
TV  
TV  
PICTURE  
NAVI  
Number  
buttons  
VOL +/–  
2
Release TV [/1.  
TIME/TEXT  
Code numbers of controllable TVs  
If more than one code number is listed, try  
entering them one at a time until you find the  
one that works with your TV.  
CLEAR  
AUDIO SUBTITLE  
MENU  
TOP MENU  
RETURN  
DISPLAY  
Manufacturer Code number  
Sony  
01 (default)  
02  
You can control your TV using the buttons  
below.  
Hitachi  
LG/Goldstar/NEC 04  
MGA/Mitsubishi 13  
By pressing  
TV [/1  
You can  
Turn the TV on or off  
Adjust the volume of the TV  
Panasonic  
Philips  
Pioneer  
RCA  
19  
21  
16  
10  
20  
18  
07  
VOL +/–  
TV INPUT  
(input select)  
Switch the TV’s input source  
between the TV and other  
input sources  
b
Samsung  
Sharp  
Depending on the connected unit, you may not be  
able to control your TV using all or some of the  
buttons on the supplied remote.  
Toshiba  
b
• When you replace the batteries of the remote, the  
code number you have set may be reset to the  
default setting. Set the appropriate code number  
again.  
• Depending on the connected unit, you may not be  
able to control your TV using all or some of the  
buttons on the supplied remote.  
11US  
 
     
Step 4: Quick Setup  
Follow the steps below to make the minimum number of basic adjustments for using the player.  
To skip an adjustment, press >. To return to the previous adjustment, press ..  
TV  
PICTURE  
NAVI  
TV  
INPUT  
TIME/TEXT  
CLEAR  
AUDIO SUBTITLE  
MENU  
TOP MENU  
ENTER  
RETURN  
DISPLAY  
1
2
Turn on the TV.  
5
Press X/x to select a language.  
The player displays the menu and  
subtitles in the selected language.  
Press [/1.  
The player turns on.  
6
Press ENTER.  
The Setup Display for selecting the  
aspect ratio of the TV to be connected  
appears.  
3
Switch the input selector on your  
TV so that the signal from the  
player appears on the TV screen.  
“Press [ENTER] to run QUICK SETUP”  
appears at the bottom of the screen. If this  
message does not appear, select  
“QUICK” under “SETUP” in the Control  
Menu to run Quick Setup (page 17).  
SCREEN SETUP  
4:3 LETTER BOX  
4:3 LETTER BOX  
4:3 PAN SCAN  
16:9  
TV TYPE:  
SCREEN SAVER:  
BACKGROUND:  
BLACK LEVEL:  
BLACK LEVEL (COMPONENT OUT):  
PROGRESSIVE (COMPONENT OUT ONLY): OFF  
OFF  
MODE (PROGRESSIVE):  
4:3 OUTPUT:  
AUTO  
FULL  
4
Press ENTER without inserting a  
disc.  
The Setup Display for selecting the  
language used in the on-screen display  
appears.  
7
Press X/xto select the setting that  
matches your TV type.  
If you have a 4:3 standard TV  
• 4:3 LETTER BOX or 4:3 PAN SCAN  
LANGUAGE SETUP  
OSD:  
ENGLISH  
ENGLISH  
MENU:  
AUDIO:  
SUBTITLE:  
If you have a wide-screen TV or a 4:3  
standard TV with a wide-screen mode  
• 16:9 (page 27)  
FRENCH  
SPANISH  
PORTUGUESE  
12US  
 
   
8
9
Press ENTER.  
11Press ENTER.  
The Setup Display for selecting the type  
of jack used to connect your audio  
component such as an amplifier  
(receiver) appears.  
“DTS” is selected.  
AUDIO SETUP  
AUDIO DRC:  
DOWNMIX:  
STANDARD  
DOLBY SURROUND  
DIGITAL OUT:  
DOLBY DIGITAL:  
DTS:  
ON  
DOLBY DIGITAL  
Is this player connected to an amplifier  
(receiver) ? Select the type of jack you  
are using.  
OFF  
OFF  
ON  
48kHz/96kHz PCM:  
YES  
AUDIO OUTPUT L/R  
DIGITAL OUTPUT  
NO  
12Press X/x to select whether or  
not you wish to send a DTS signal  
to your audio component.  
Press X/xto select the type of jack  
(if any) you are using to connect to  
an audio component, then press  
ENTER.  
If your audio component has a DTS  
decoder, select “ON.” Otherwise, select  
“OFF.”  
If you did not connect an audio  
component, select “NO,” then go to step  
13.  
If you connected an audio component  
using just an audio cable, select “YES:  
AUDIO OUTPUT L/R,” then go to step  
13.  
13Press ENTER.  
Quick Setup is finished and connections  
are complete.  
If you connected an audio component  
using a digital coaxial cable, select  
“YES: DIGITAL OUTPUT.”  
10Press X/x to select the type of  
Dolby Digital signal you wish to  
send to your audio component.  
If your audio component has a Dolby  
Digital decoder, select “DOLBY  
DIGITAL.” Otherwise, select “D-PCM.”  
AUDIO SETUP  
AUDIO DRC:  
DOWNMIX:  
STANDARD  
DOLBY SURROUND  
ON  
DIGITAL OUT:  
DOLBY DIGITAL:  
DTS:  
DOLBY DIGITAL  
DOLBY DIGITAL  
D-PCM  
48kHz/96kHz PCM:  
13US  
 
To stop playback  
Press x.  
Playback  
To pause playback  
Press X.  
Playing Discs  
z
You can have the player turned off automatically  
whenever you leave it in stop mode for more than  
30 minutes. To turn this function on or off, set  
“AUTO POWER OFF” in “CUSTOM SETUP” to  
“ON” or “OFF” (page 29).  
Depending on the DVD or VIDEO CD, some  
operations may be different or restricted.  
Refer to the operating instructions supplied  
with your disc.  
b
Discs created on DVD recorders must be correctly  
finalized before they can be played. For more  
information about finalizing, refer to the operating  
instructions supplied with the DVD recorder.  
TV  
INPUT  
TV  
PICTURE  
NAVI  
Number  
buttons  
TIME/TEXT  
CLEAR  
AUDIO SUBTITLE  
MENU  
Note on playing DTS sound tracks on a  
DVD VIDEO  
TOP MENU  
DTS audio signals are output only through the  
DIGITAL OUT (COAXIAL) jack.  
ENTER  
RETURN  
DISPLAY  
RETURN  
To resume playback from the point where  
you stopped the disc (Multi-disc Resume)  
When you press N again after you stop  
playback, the player starts playback from the  
point when you pressed x.  
1
2
Press Z on the player, and place  
the disc on the disc tray.  
z
• To play from the beginning of the disc, press x  
twice, then press N.  
• With DVD VIDEOs and VIDEO CDs, the player  
stores the point where you stopped the disc for up  
to 6 discs and resumes playback the next time you  
insert the same disc. If you store a resume  
playback point for the seventh disc, the resume  
playback point for the first disc is deleted.  
Playback side  
facing down  
b
• “MULTI-DISC RESUME” in “CUSTOM  
SETUP” must be set to “ON” (default) for this  
function to work (page 29).  
• Resume Play does not work during Shuffle Play  
and Program Play.  
• With some discs, Resume Play may not work,  
depending on the point you stop playback, or if  
you press [/1.  
Press N.  
The disc tray closes. The player starts  
playback (continuous play). Adjust the  
volume on the TV or the audio  
component.  
Depending on the disc, a menu may  
appear on the TV screen. For DVD  
VIDEOs, see page 7. For VIDEO CDs,  
14US  
 
               
To play VIDEO CDs With PBC Functions  
(PBC Playback)  
PBC (Playback Control) allows you to play  
VIDEO CDs interactively by following the  
menu on the TV screen.  
When you start playing a VIDEO CD with  
PBC functions, the menu for your selection  
appears.  
Select an item using the number buttons, and  
press ENTER. Then, follow the instructions  
in the menu for interactive operations (press  
N when “Press SELECT” appears).  
Refer to the instructions supplied with the  
disc, as the operating procedure may differ  
depending on the VIDEO CD.  
To return to the menu  
Press O RETURN.  
z
To play without using PBC, press ./> or the  
number buttons while the player is stopped to select  
a track, then press N or ENTER.  
“Play without PBC” appears on the TV screen and  
the player starts continuous play. You cannot play  
still pictures such as a menu.  
To return to PBC playback, press x twice then  
press N.  
To lock the disc tray (Child Lock)  
You can lock the disc tray to prevent children  
from opening it.  
When the player is in standby mode, press O  
RETURN, ENTER, and [/1 on the remote.  
The player turns on and “  
” (LOCKED)  
appears on the front panel display. The Z  
button on the player does not work while the  
Child Lock is set.  
To unlock the disc tray, press O RETURN,  
ENTER, and [/1 again when the player is in  
standby mode.  
b
Even if you select “RESET” under “SETUP” in the  
Control Menu (page 17), the disc tray remains  
locked.  
15US  
,continued  
 
         
Control Menu display (DISPLAY)  
Use the Control Menu to select a function and to view related information. Press DISPLAY  
repeatedly to turn on or change the Control Menu display as follows:  
, Control Menu display 1  
m
Control Menu display 2 (Except CD)  
m
Control Menu display off  
The Control Menu display 1 and 2 will show different items depending on the disc type.  
Example: Control Menu display 1 when playing a DVD VIDEO.  
Press X/x to select the Control Menu item, then press ENTER.  
For details about the item, see “List of Control Menu items” (page 17, 18).  
2
Currently playing chapter number*  
1
Currently playing title number*  
1
Total number of titles*  
Playback status  
(N Playback,  
X Pause,  
2
Total number of chapters*  
x Stop, etc.)  
Control Menu items  
Type of disc  
being played*  
3
(
)
)
1 2 2 7  
DVD VIDEO  
(
1 8 3 4  
4
Playing time*  
Current setting  
T
1 : 3 2 : 5 5  
Selected item  
OFF  
OFF  
SET  
ON  
Options  
Function name of  
selected Control  
Menu item  
PROGRAM  
ENTER  
DISPLAY  
Quit:  
Operation message  
1
* Displays the scene number for VIDEO CDs  
(PBC is on), track number for VIDEO CDs/CDs,  
album number for DATA discs.  
2
* Displays the index number for VIDEO CDs,  
MP3 audio track number or JPEG image file  
number for DATA discs.  
* Displays Super VCD as “SVCD.”  
3
4
* Displays the date for JPEG files.  
16US  
 
       
A-B REPEAT (page 21)  
Specifies the parts you want to play  
repeatedly.  
List of Control Menu items  
Item  
Item Name, Function  
TITLE/SCENE/TRACK  
CHAPTER/INDEX  
SHARPNESS (page 22)  
Exaggerates the outline of the image  
to produce a sharper picture.  
PARENTAL CONTROL  
Set to prohibit playback on this  
player.  
TRACK  
Selects the title, scene, track,  
chapter, or index to be played.  
1
Press X/x to select the search  
method.  
SETUP (page 12, 26)  
QUICK:  
Use Quick Setup to choose the  
desired language of the on-screen  
display, the aspect ratio of the TV  
and the audio output signal.  
“** (**)” is selected (** refers to a  
number).  
2
Press ENTER.  
“** (**)” changes to “-- (**).”  
CUSTOM:  
3
Press the number buttons to  
select the number you want to  
search.  
In addition to the Quick Setup  
setting, you can adjust various other  
settings.  
4
Press ENTER.  
RESET:  
Returns the settings in “SETUP” to  
the default setting.  
TIME/TEXT  
Checks the elapsed time and the  
remaining playback time.  
Input the time code for picture and  
music searching (DVD only).  
ZOOM  
Magnifies the image up to four times  
the original size, and scroll using C/  
X/x/c.  
To return to normal view, press  
CLEAR.  
1
2
Press ENTER.  
Input the time code using the  
number buttons, then press  
ENTER.  
This function is available for all  
pictures except a background image.  
For example, to find the scene  
at 2 hours, 10 minutes, and 20  
seconds after the beginning,  
just enter “2:10:20.”  
ANGLE  
Changes the angle.  
CUSTOM PICTURE MODE  
Adjusts the video signal from the  
player. You can select the picture  
quality that best suits the program  
you are watching.  
b
You cannot search for a scene on a  
DVD+RW/DVD+R/DVD+R DL  
using the time code.  
ORIGINAL/PLAY LIST  
Selects the type of titles (DVD-VR  
mode) to be played, the ORIGINAL  
one, or an edited PLAY LIST.  
PROGRAM (page 19)  
Selects the title, chapter, or track to  
play in the order you want.  
SHUFFLE (page 20)  
Plays the title, chapter, or track in  
random order.  
Plays the entire disc (all titles/all  
tracks/all albums) repeatedly or one  
title/chapter/track/album repeatedly.  
17US  
,continued  
 
                                           
Items for DATA discs  
Item Item Name, Function  
TVS  
Selects surround sound effect when  
connecting a stereo TV or 2 front  
speakers. This only works when  
playing a multichannel Dolby audio  
soundtrack. Furthermore, if the  
player is set up to output the signal  
from the DIGITAL OUT  
(COAXIAL) jack, the surround  
effect will only be heard when  
“DOLBY DIGITAL” is set to  
“D-PCM” in “AUDIO SETUP”  
ALBUM  
Selects the album that contains MP3  
audio tracks and JPEG image file to  
be played.  
FILE  
Selects the JPEG image file to be  
played.  
DATE  
Displays the date the picture was  
taken by a digital camera.  
The default setting is underlined.  
• OFF  
Cancels the setting.  
INTERVAL (page 25)  
Specifies the duration for which the  
slides are displayed on the screen.  
• TVS DYNAMIC THEATER  
• TVS DYNAMIC  
• TVS WIDE  
This mode is effective when the  
distance between the front L and R  
speakers is short, such as with built-  
in speakers on a stereo TV.  
EFFECT (page 25)  
Selects the effects to be used for  
changing slides during a slide show.  
MODE (MP3, JPEG)  
Selects the data type; MP3 audio  
track (AUDIO), JPEG image file  
(IMAGE), or both (AUTO) to be  
played when playing a DATA disc.  
• TVS NIGHT  
This feature is useful when you want  
to hear the dialog and enjoy the  
surround sound effects of “TVS  
WIDE” at low volume.  
• TVS STANDARD  
Use this setting when you want to  
use TVS with 2 separate speakers.  
b
• When you select one of the TVS  
modes, turn off the surround setting  
of the connected TV or audio  
component.  
• The TVS effects do not work when  
using the Fast Play or Slow Play  
functions, even though you can  
change the TVS modes.  
z
The Control Menu icon indicator lights up in green  
t
when you select any item  
except “OFF” (“PROGRAM,” “SHUFFLE,”  
“REPEAT,” “A-B REPEAT,” “SHARPNESS,”  
“ZOOM,” “TVS” only). The “ORIGINAL/PLAY  
LIST” indicator lights up in green when you select  
“PLAY LIST” (default setting). The “ANGLE”  
indicator lights up in green when you can change  
the angle. The “CUSTOM PICTURE MODE”  
indicator lights up in green when any setting other  
than “STANDARD” is selected.  
18US  
 
                 
3 Select the title, chapter, or track you  
want to program.  
Various Play Mode  
Functions  
When playing a DVD VIDEO  
For example, select chapter “03” of title  
“02.”  
You can set the following play modes:  
• Program Play (page 19)  
Press X/x to select “02” under “T,” then  
press ENTER.  
• Shuffle Play (page 20)  
• Repeat Play (page 21)  
• A-B Repeat Play (page 21)  
PROGRAM  
T
C
ALL CLEAR  
– –  
– –  
ALL  
1. TITLE  
2. TITLE  
3. TITLE  
4. TITLE  
5. TITLE  
6. TITLE  
7. TITLE  
– –  
– –  
– –  
– –  
– –  
– –  
01  
02  
03  
04  
05  
06  
01  
02  
03  
04  
05  
b
The play mode is canceled when:  
– you open the disc tray.  
– you press [/1 and the player enters standby mode.  
Creating your own  
program (Program Play)  
Next, press X/x to select “03” under “C,”  
then press ENTER.  
PROGRAM  
T
ALL CLEAR  
1. TITLE 0 2 0 3  
You can play the contents of a disc in the  
order you want. You can program up to 99  
titles, chapters, and tracks.  
– –  
– –  
– –  
– –  
– –  
– –  
– –  
2. TITLE  
3. TITLE  
4. TITLE  
5. TITLE  
6. TITLE  
7. TITLE  
01  
02  
03  
04  
05  
1 After selecting  
(PROGRAM)  
on the Control Menu (page 16), press  
X/x to select “SET t,” then press  
ENTER.  
Selected title and chapter  
“TRACK” is displayed when you play  
a VIDEO CD or CD.  
When playing a VIDEO CD or CD  
For example, select track “02.”  
Press X/x to select “02” under “T,” then  
press ENTER.  
PROGRAM  
T
ALL CLEAR  
– –  
1. TITLE  
2. TITLE  
3. TITLE  
4. TITLE  
– –  
– –  
– –  
– –  
– –  
– –  
Selected track  
01  
02  
03  
04  
05  
0:15:30  
T
PROGRAM  
5. TITLE  
6. TITLE  
7. TITLE  
ALL CLEAR  
1. TRACK  
2. TRACK  
3. TRACK  
4. TRACK  
5. TRACK  
6. TRACK  
7. TRACK  
– –  
0 2  
– –  
– –  
– –  
– –  
– –  
– –  
01  
02  
03  
04  
05  
Titles or tracks recorded on a disc  
2 Press c.  
The cursor moves to the title or track row  
“T” (in this case, “01”).  
Total time of the programmed tracks  
PROGRAM  
4 Repeat steps 2 to 3, to program other  
titles, chapters, or tracks.  
T
C
ALL CLEAR  
1. TITLE  
– –  
– –  
01  
02  
03  
04  
05  
ALL  
– –  
– –  
– –  
– –  
– –  
– –  
2. TITLE  
3. TITLE  
4. TITLE  
5. TITLE  
6. TITLE  
7. TITLE  
01  
02  
03  
04  
05  
06  
The programmed titles, chapters, and  
tracks are displayed in the selected order.  
Chapters recorded on a disc  
19US  
,continued  
 
       
5 Press N.  
Playing in random order  
(Shuffle Play)  
You can have the player “shuffle” titles,  
chapters, or tracks. Subsequent “shuffling”  
may produce a different playing order.  
Program Play begins.  
When the program ends, you can restart  
the same program again by pressing N.  
To return to normal play  
Press CLEAR, or select “OFF” in step 1. To  
play the same program again, select “ON” in  
step 1 and press ENTER.  
1 After selecting  
(SHUFFLE) on  
the Control Menu (page 16), press X/  
x to select the item to be shuffled.  
When playing a DVD VIDEO  
• TITLE  
• CHAPTER  
To change or cancel a program  
1
Follow step 1 of “Creating your own  
When playing a VIDEO CD or CD  
• TRACK  
2
Select the program number of the title,  
chapter, or track you want to change or  
cancel using X/x and press c. If you  
want to delete the title, chapter, or track  
from the program, press CLEAR.  
When Program Play is activated  
• ON: shuffles titles, chapters, or tracks  
selected in Program Play.  
2 Press ENTER.  
3
Follow step 3 of “Creating your own  
program (Program Play)” for new  
programming. To cancel a program,  
select “--” under “T,” then press ENTER.  
Shuffle Play starts.  
To return to normal play  
Press CLEAR, or select “OFF” in step 1.  
To cancel all of the titles, chapters, or  
tracks in the programmed order  
Press X and select “ALL CLEAR” in step 2 of  
“Creating your own program (Program  
Play)” and press ENTER.  
z
• You can set Shuffle Play while the player is  
stopped. After selecting the “SHUFFLE” option,  
press N. Shuffle Play starts.  
• Up to 200 chapters in a disc can be played in  
random order when “CHAPTER” is selected.  
z
You can perform Repeat Play or Shuffle Play of  
programmed titles, chapters, or tracks. During  
Program Play, follow the steps of Repeat Play  
(page 21) or Shuffle Play (page 20).  
b
You cannot use this function with VIDEO CDs or  
Super VCDs with PBC playback.  
b
• When you program tracks on a Super VCD, the  
total playing time is not displayed.  
• You cannot use this function with VIDEO CDs or  
Super VCDs with PBC playback.  
20US  
 
   
Playing repeatedly  
(Repeat Play)  
Repeating a specific  
portion (A-B Repeat Play)  
You can play all of the titles or tracks on a  
disc, or a single title, chapter, or track  
repeatedly.  
You can use a combination of Shuffle or  
Program Play modes.  
You can play a specific portion of a title,  
chapter or track repeatedly.  
1 After selecting  
(A-B REPEAT)  
on the Control Menu (page 16), press  
X/x to select “SET t,” then press  
ENTER.  
1 After selecting  
(REPEAT) on  
the Control Menu (page 16), press X/  
x to select the item to be repeated.  
• DISC: repeats all of the titles, tracks, or  
albums. (Select ORIGINAL or PLAY  
LIST in DVD-VR mode.)  
The “A-B REPEAT” setting bar appears.  
A 18 - 1:32:30  
B
• TITLE: repeats the current title on a  
disc.  
• CHAPTER: repeats the current chapter.  
• TRACK: repeats the current track.  
• ALBUM: repeats the current album.  
2 During playback, when you find the  
starting point (point A) of the portion to  
be played repeatedly, press ENTER.  
The starting point (point A) is set.  
When Program Play or Shuffle Play is  
activated  
• ON: repeats Program Play or Shuffle  
Play.  
A 18 - 1:32:55 B 18 - 1:33:05  
2 Press ENTER.  
Repeat Play starts.  
3 When you reach the ending point  
(point B), press ENTER again.  
The set points are displayed and the  
player starts repeating this specific  
portion.  
To return to normal play  
Press CLEAR, or select “OFF” in step 1.  
b
You cannot use this function with VIDEO CDs or  
Super VCDs with PBC playback.  
To return to normal play  
Press CLEAR, or select “OFF” in step 1.  
b
• A-B Repeat Play does not work across multiple  
titles.  
• You may not set A-B Repeat Play for contents in  
DVD-VR mode that contains still pictures.  
21US  
 
           
b
The “BRIGHTNESS” setting is not effective if you  
connect the player via the VIDEO OUT jack and  
select “PROGRESSIVE (COMPONENT OUT  
ONLY)” to “ON” using the “SCREEN SETUP.”  
Customizing the  
Playback Configuration  
Sharpening the picture  
(SHARPNESS)  
Adjusting the playback  
picture (CUSTOM PICTURE MODE)  
You can enhance the outlines of images to  
produce a sharper picture.  
You can adjust the video signal from the  
player to obtain the picture quality you want.  
1 After selecting  
(SHARPNESS)  
on the Control Menu (page 16), press  
X/x to select a level.  
1 After selecting  
(CUSTOM  
PICTURE MODE) on the Control Menu  
(page 16), press X/x to select the  
setting you want.  
The default setting is underlined.  
• OFF: cancels this option.  
• 1: enhances the outline.  
The default setting is underlined.  
• STANDARD: displays a standard  
picture.  
• DYNAMIC 1: produces a bold  
dynamic picture by increasing the  
picture contrast and the color intensity.  
• DYNAMIC 2: produces a more  
dynamic picture than DYNAMIC 1 by  
further increasing the picture contrast  
and color intensity.  
• CINEMA 1: enhances details in dark  
areas by increasing the black level.  
• CINEMA 2: white colors become  
brighter and black colors become  
richer, and the color contrast is  
increased.  
• 2: enhances the outline more than 1.  
2 Press ENTER.  
The selected setting takes effect.  
Locking discs (PARENTAL  
CONTROL)  
Playback of some DVD VIDEOs can be  
limited according to a predetermined level  
such as the age of the users. The  
“PARENTAL CONTROL” function allows  
you to set a playback limitation level.  
1 After selecting  
(PARENTAL  
CONTROL) on the Control Menu  
(page 16), press X/x to select  
“PLAYER t,” then press ENTER.  
The password is required.  
• MEMORY: adjusts the picture in  
greater detail.  
PICTURE  
Changes the contrast.  
BRIGHTNESS Changes the overall  
brightness.  
2 Enter or re-enter your 4-digit password  
using the number buttons, then press  
ENTER.  
COLOR  
HUE  
Makes the colors  
deeper or lighter.  
Changes the color  
balance.  
The display for setting the playback  
limitation level appears.  
3 Press X/x to select “STANDARD,”  
2 Press ENTER.  
then press ENTER.  
The selected setting takes effect.  
The selection items for “STANDARD”  
are displayed.  
z
When you watch a movie, “CINEMA 1” or  
“CINEMA 2” is recommended.  
22US  
 
               
4 Press X/x to select a geographic area  
as the playback limitation level, then  
press ENTER.  
Playing MP3 Audio and  
JPEG Images  
The area is selected.  
When you select “OTHERS t,” select  
and enter a standard code in the table on  
page 37 using the number buttons.  
You can play MP3 audio tracks and JPEG  
image files on DATA discs.  
You can enjoy JPEG images as a slide show.  
5 Press X/x to select “LEVEL,” then  
press ENTER.  
PICTURE  
TV  
TV  
PICTURE  
NAVI  
INPUT  
NAVI  
The selection items for “LEVEL” are  
displayed.  
TIME/TEXT  
6 Select the level you want using X/x,  
TIME/TEXT  
SUBTITLE  
MENU  
CLEAR  
AUDIO SUBTITLE  
MENU  
then press ENTER.  
CLEAR  
TOP MENU  
Parental Control setting is complete.  
The lower the value, the stricter the  
limitation.  
ENTER  
RETURN  
DISPLAY  
RETURN  
DISPLAY  
To turn off the Parental Control function  
Set “LEVEL” to “OFF” in step 6.  
To set or change your password  
After selecting “PARENTAL CONTROL”  
on the Control Menu, select “PASSWORD  
t,” then press ENTER.  
z
You can view the disc information while playing  
MP3 audio tracks and JPEG image files using  
TIME/TEXT (page 6).  
z
If you forget your password, remove the disc and  
repeat step 1 of “Locking discs (PARENTAL  
CONTROL).” When you are asked to enter your  
password, enter “199703” using the number  
buttons, then press ENTER. The display will ask  
you to enter a new 4-digit password. After you enter  
a new 4-digit password, replace the disc in the  
player and press N. When the display for entering  
your password appears, enter your new password.  
b
DATA CDs recorded in KODAK Picture CD  
format automatically start playing when inserted.  
1
Press MENU.  
The list of albums on the disc appears.  
When an album is being played, its title is  
shaded.  
b
Depending on the disc, you may be asked to change  
the parental control level while playing the disc. In  
this case, enter your password, then change the  
level. If the Resume Play mode is canceled, the  
level returns to the previous level.  
1
( 15)  
Album 1  
Album 2  
Album 3  
Album 4  
Album 5  
Album 6  
Album 7  
Album 8  
2
Press X/x to select the album.  
23US  
,continued  
 
     
3
Press N.  
Playback starts from the selected album.  
The JPEG images in the selected album  
start playing as a slide show.  
Selecting a JPEG image file  
1 Press MENU.  
The list of albums on the disc appears.  
To select a specific MP3 audio track,  
press ENTER and press X/x to select a  
track, then press ENTER.  
To select a specific JPEG image file, see  
2 Press X/x to select the album, then  
press PICTURE NAVI.  
The image files in the album appear in 16  
subscreens. A scroll box is displayed on  
the right.  
To stop playback  
Press x.  
1
2
3
4
5
6
7
8
To go to the next or previous page  
Press c or C.  
9
10  
14  
11  
15  
12  
16  
To return to the previous display  
Press O RETURN.  
13  
To display additional images, select a  
bottom image and press x. To return to a  
previous image, select a top image and  
press X.  
To go to the next or previous MP3 audio  
track  
Press > or . during playback. You can  
select the first track of the next album by  
pressing > during playback of the last  
track of the current album.  
Note that you cannot return to the previous  
album by using ., and that you need to  
select the previous album from the album list.  
3 PressC/X/x/cto select the image you  
want to view, and press ENTER.  
The selected image appears.  
To go to the next or previous JPEG image  
file  
Press C or c during playback. You can select  
the first file of the next album by pressing c  
during playback of the last file of the current  
album.  
Note that you cannot return to the previous  
album by using C, and that you need to select  
the previous album from the album list.  
To turn on or off the display  
Press MENU repeatedly.  
z
Of the selected album, you can select to play only  
the MP3 audio tracks, JPEG image files, or both, by  
setting “MODE (MP3, JPEG)” (page 18).  
To rotate a JPEG image  
Press X/x while viewing the image. Each  
time you press X, the image rotates  
counterclockwise by 90 degrees.  
To return to normal view, press CLEAR.  
Note that the view also returns to normal if  
you press C/c to go to the next or previous  
image.  
24US  
 
   
To display JPEG image information  
Press SUBTITLE while viewing JPEG image  
files.  
The file name, camera maker/model, date,  
time, picture resolution, file size, camera  
setting information (ISO speed rating,  
Exposure time, F Number, Exposure bias, or  
Focal length) of the picture are displayed on  
the screen.  
Setting the pace for a  
slide show (INTERVAL)  
You can set the time the slides are displayed  
on the screen.  
1 After selecting  
(INTERVAL) on  
the Control Menu (page 16), press X/  
x to select a setting.  
is displayed when the picture was taken  
using flash.  
The default setting is underlined.  
• NORMAL: sets to standard duration.  
• FAST: sets a duration shorter than  
NORMAL.  
is displayed when the image is  
automatically rotated.  
To hide the information, press SUBTITLE.  
Note that the above information may not  
appear depending on the digital camera.  
• SLOW 1: sets a duration longer than  
NORMAL.  
• SLOW 2: sets a duration longer than  
SLOW 1.  
To stop viewing the JPEG image  
Press x.  
2 Press ENTER.  
b
Selecting the slides’  
appearance (EFFECT)  
PICTURE NAVI does not work if “AUDIO (MP3)”  
is selected in “MODE (MP3, JPEG)” (page 18).  
You can select the way the slides are  
displayed during a slide show.  
1 After selecting  
(EFFECT) on  
the Control Menu (page 16), press X/  
x to select a setting.  
The default setting is underlined.  
• MODE 1: the images randomly cycle  
through the effects.  
• MODE 2: the next image slides over the  
previous image.  
• MODE 3: the image sweeps in from top  
to bottom.  
• MODE 4: the image sweeps in from left  
to right.  
• MODE 5: the image stretches out from  
the center of the screen.  
• OFF: turns off this function.  
2 Press ENTER.  
25US  
 
           
LANGUAGE SETUP  
Settings and Adjustments  
“LANGUAGE SETUP” allows you to set  
various languages for the on-screen display or  
sound track.  
Using the Setup Display  
By using the Setup Display, you can make  
various adjustments to items such as picture  
and sound. You can also set a language for the  
subtitles and the Setup Display, among other  
things.  
Select “LANGUAGE SETUP” in the Setup  
Display.  
OSD (On-Screen Display)  
Switches the display language on the screen.  
For details on each Setup Display item, see  
pages from 26 to 31.  
MENU (DVD VIDEO only)  
You can select the desired language for the  
disc’s menu.  
b
Playback settings stored in the disc take priority  
over the Setup Display settings and not all of the  
functions described may work.  
AUDIO (DVD VIDEO only)  
Switches the language of the sound track.  
When you select “ORIGINAL,” the language  
given priority in the disc is selected.  
1
2
Press DISPLAY when the player is  
in stop mode.  
SUBTITLE (DVD VIDEO only)  
Switches the language of the subtitle recorded  
on the DVD VIDEO.  
When you select “AUDIO FOLLOW,” the  
language for the subtitles changes according  
to the language you selected for the sound  
track.  
The Control Menu appears.  
Press X/x to select  
(SETUP), then press ENTER.  
The options for “SETUP” appear.  
• QUICK: makes the basic adjustments  
z
If you select “OTHERS t” in “MENU,”  
“SUBTITLE,” or “AUDIO,” select and enter a  
page 37 using the number buttons.  
• CUSTOM: makes various adjustments.  
• RESET: resets all the settings explained  
on pages 26 to 31.  
3
Press X/x to select “CUSTOM,”  
then press ENTER.  
The Setup Display appears.  
Select the setup category and adjust each  
item following the instruction on pages  
26 to 31.  
b
If you select a language in “MENU,”  
“SUBTITLE,” or “AUDIO” that is not recorded on  
a DVD VIDEO, one of the recorded languages will  
be automatically selected.  
LANGUAGE SETUP  
OSD:  
ENGLISH  
ENGLISH  
ORIGINAL  
ENGLISH  
MENU:  
AUDIO:  
SUBTITLE:  
26US  
 
                   
SCREEN SAVER  
The screen saver image appears when you  
leave the player in pause or stop mode for 15  
minutes, or when you play a CD, or DATA  
disc (MP3 audio) for more than 15 minutes.  
The screen saver will help prevent your  
display device from becoming damaged  
(ghosting). Press N to turn off the screen  
saver.  
SCREEN SETUP  
Choose settings according to the TV to be  
connected.  
Select “SCREEN SETUP” in the Setup  
Display. To use the display, see “Using the  
The default settings are underlined.  
ON  
Turns on the screen saver.  
Turns off the screen saver.  
OFF  
TV TYPE  
Selects the aspect ratio of the connected TV  
(4:3 standard or wide).  
BACKGROUND  
Selects the background color or picture on the  
TV screen when the player is in stop mode or  
while playing a CD, or DATA disc (MP3  
audio).  
4:3  
LETTER  
BOX  
Select this when you connect a  
4:3 screen TV. Displays a wide  
picture with bands on the upper  
and lower portions of the  
screen.  
JACKET  
PICTURE  
The jacket picture (still picture)  
appears, but only when the  
jacket picture is already  
4:3  
Select this when you connect a  
PAN SCAN 4:3 screen TV. Automatically  
displays the wide picture on the  
entire screen and cuts off the  
recorded on the disc (CD-  
EXTRA, etc.). If the disc does  
not contain a jacket picture, the  
“GRAPHICS” picture appears.  
portions that do not fit.  
16:9  
Select this when you connect a  
wide-screen TV or a TV with a  
wide mode function.  
GRAPHICS A preset picture stored in the  
player appears.  
BLUE  
The background color is blue.  
The background color is black.  
BLACK  
4:3 LETTER BOX  
BLACK LEVEL  
Selects the black level (setup level) for the  
video signals output from the jacks other than  
COMPONENT VIDEO OUT.  
4:3 PAN SCAN  
ON  
Sets the black level of the  
output signal to the standard  
level.  
16:9  
OFF  
Lowers the standard black  
level. Use this when the picture  
becomes too white.  
b
Depending on the DVD, “4:3 LETTER BOX” may  
be selected automatically instead of “4:3 PAN  
SCAN” or vice versa.  
27US  
,continued  
 
                 
BLACK LEVEL (COMPONENT OUT)  
Selects the black level (setup level) for the  
video signals output from the COMPONENT  
VIDEO OUT jacks. You cannot select this  
when the player outputs progressive signals  
(page 9).  
MODE (PROGRESSIVE)  
In order for these images to appear natural on  
your screen when output in progressive  
mode, the progressive video signal needs to  
be converted to match the type of DVD  
software that you are watching.  
This setting is effective only when you set  
“PROGRESSIVE (COMPONENT OUT  
ONLY)” in “SCREEN SETUP” to “ON.”  
OFF  
Sets the black level of the  
output signal to the standard  
level. Normally select this  
position.  
AUTO  
Automatically detects the  
software type (film-based or  
video-based) and selects the  
appropriate conversion mode.  
Normally, select this position.  
ON  
Raises the standard black level.  
Use this setting when the  
picture appears too dark.  
VIDEO  
Fixes the conversion mode to  
the mode for video-based  
software.  
PROGRESSIVE (COMPONENT OUT  
ONLY)  
If your TV accepts progressive (480p) format  
signals, set “PROGRESSIVE  
4:3 OUTPUT  
This setting is effective only when you set  
“TV TYPE” in “SCREEN SETUP” to  
“16:9.”  
(COMPONENT OUT ONLY)” to “ON.”  
Note that you must connect to a progressive  
format TV using the COMPONENT VIDEO  
OUT jacks (page 9).  
Adjust this to watch 4:3 aspect ratio  
progressive signals. If you can change the  
aspect ratio on your progressive format  
(480p) compatible TV, change the setting on  
your TV, not the player. This setting is  
effective only when “PROGRESSIVE  
(COMPONENT OUT ONLY)” is set to  
“ON” in “SCREEN SETUP.”  
OFF  
ON  
To output normal (interlace)  
signals.  
To output progressive signals.  
To output progressive signals  
1
Select “PROGRESSIVE  
(COMPONENT OUT ONLY),” and  
press ENTER.  
FULL  
Select this when you can  
change the aspect ratio on your  
TV.  
2
3
Select “ON,” and press ENTER.  
The display asks for confirmation.  
NORMAL  
Select this when you cannot  
change the aspect ratio on your  
TV. Shows a 16:9 aspect ratio  
signal with black bands on left  
and right sides of the image.  
Select “Start,” and press ENTER.  
The video switches to a progressive  
signal for 5 seconds.  
4
If the picture appears normal, select  
“YES,” and press ENTER.  
If not, select “NO,” and press ENTER.  
To reset the setting  
16:9 aspect ratio TV  
If the picture does not appear normal or goes  
blank, press [/1 to turn off the player, and  
enter “369” using the number buttons on the  
remote, then press [/1 to turn on the player  
again.  
28US  
 
             
b
• When you set the item to “AUTO,” the language  
may change. The “TRACK SELECTION” setting  
has higher priority than the “AUDIO” settings in  
“LANGUAGE SETUP” (page 26).  
• If you set “DTS” to “OFF” (page 31), the DTS  
sound track is not played even if you set “TRACK  
SELECTION” to “AUTO.”  
• If PCM, DTS, and Dolby Digital sound tracks  
have the same number of channels, the player  
selects PCM, DTS, and Dolby Digital sound  
tracks in this order.  
CUSTOM SETUP  
Use this to set up playback related and other  
settings.  
Select “CUSTOM SETUP” in the Setup  
Display. To use the display, see “Using the  
The default settings are underlined.  
AUTO POWER OFF  
MULTI-DISC RESUME (DVD VIDEO/  
VIDEO CD only)  
Switches the Multi-disc Resume setting on or  
off. Resume playback can be stored in  
memory for up to 6 different DVD VIDEOs/  
VIDEO CDs (page 14).  
Switches the Auto Power Off setting on or  
off.  
OFF  
ON  
Switches this function off.  
The player enters standby mode  
when left in stop mode for more  
than 30 minutes.  
ON  
Stores the resume setting in  
memory for up to 6 discs.  
OFF  
Does not store the resume  
AUTO PLAY  
setting in memory. Playback  
restarts at the resume point only  
for the current disc in the player.  
Switches the Auto Play setting on or off. This  
function is useful when the player is  
connected to a timer (not supplied).  
OFF  
ON  
Switches this function off.  
b
If you run Quick Setup, Multi-disc Resume setting  
stored in memory may return to the default settings.  
Automatically starts playback  
when the player is turned on by  
a timer (not supplied).  
PAUSE MODE (DVDs only)  
Selects the picture in pause mode.  
AUTO  
The picture, including subjects  
that move dynamically, is  
output with no jitter. Normally  
select this position.  
FRAME  
The picture, including subjects  
that do not move dynamically,  
is output in high resolution.  
TRACK SELECTION (DVD VIDEO only)  
Gives the sound track which contains the  
highest number of channels priority when you  
play a DVD VIDEO on which multiple audio  
formats (PCM, DTS, or Dolby Digital  
format) are recorded.  
OFF  
No priority given.  
Priority given.  
AUTO  
29US  
 
                 
DIGITAL OUT  
Selects if audio signals are output via the  
DIGITAL OUT (COAXIAL) jack.  
AUDIO SETUP  
ON  
Normally, select this position.  
When you select “ON,” see  
for further settings.  
“AUDIO SETUP” allows you to set the sound  
according to the playback and connection  
conditions.  
OFF  
The influence of the digital  
circuit upon the analog circuit is  
minimal.  
Select “AUDIO SETUP” in the Setup  
Display. To use the display, see “Using the  
The default settings are underlined.  
Setting the digital output signal  
AUDIO DRC (Dynamic Range Control)  
(DVDs only)  
Makes the sound clear when the volume is  
turned down when playing a DVD that  
conforms to “AUDIO DRC.”  
This function affects the output from the  
following jacks:  
Switches the method of outputting audio  
signals when you connect a component such  
as an audio component or MD deck with a  
digital input jack.  
For connection details, see page 10.  
Select “DOLBY DIGITAL,” “DTS,” and  
“48kHz/96kHz PCM” after setting  
“DIGITAL OUT” to “ON.”  
If you connect a component that is  
incompatible with the selected audio signal, a  
loud noise (or no sound) may be heard from  
the speakers, risking damage to your ears or  
speakers.  
– AUDIO OUT L/R jacks  
– DIGITAL OUT (COAXIAL) jack only  
when “DOLBY DIGITAL” is set to “D-  
PCM” (page 30).  
STANDARD Normally, select this position.  
TV MODE  
Makes low sounds clear even if  
you turn the volume down.  
DOLBY DIGITAL (DVDs only)  
Selects the type of Dolby Digital signal.  
WIDE  
RANGE  
Gives you the feeling of being  
at a live performance.  
DOLBY  
DIGITAL  
Select this when the player is  
connected to an audio  
DOWNMIX (DVDs only)  
Switches the method for mixing down to 2  
channels when you play a DVD which has  
rear sound elements (channels) or is recorded  
in Dolby Digital format. For details on the  
rear signal components, see page 10. This  
function affects the output of the following  
jacks:  
component with a built-in  
Dolby Digital decoder.  
D-PCM  
Select this when the player is  
connected to an audio  
component without a built-in  
Dolby Digitaldecoder. You can  
select whether the signals  
conform to Dolby Surround  
(Pro Logic) or not by making  
adjustments to the  
– AUDIO OUT L/R jacks  
– DIGITAL OUT (COAXIAL) jack when  
“DOLBY DIGITAL” is set to “D-PCM”  
“DOWNMIX” item in  
“AUDIO SETUP” (page 30).  
DOLBY  
SUR-  
ROUND  
Normally, select this position.  
Multi-channel audio signals are  
output to 2 channels for enjoying  
surround sounds.  
NORMAL Multi-channel audio signals are  
downmixed to 2 channels for use  
with your stereo.  
30US  
 
                       
DTS  
Selects whether or not to output DTS signals.  
OFF  
Select this when the player is  
connected to an audio  
component without a built-in  
DTS decoder.  
ON  
Select this when the player is  
connected to an audio  
component with a built-in DTS  
decoder.  
• When you play a DVD VIDEO with DTS  
sound tracks, set “DTS” to “ON” in  
“AUDIO SETUP” (page 31).  
• If you connect the player to audio  
equipment without a DTS decoder, do not  
set “DTS” to “ON” in “AUDIO SETUP”  
(page 31). A loud noise may come out from  
the speakers, affecting your ears or causing  
the speakers to be damaged.  
48kHz/96kHz PCM (DVD VIDEO only)  
Selects the sampling frequency of the audio  
signal.  
48kHz/16bit The audio signals of DVD  
VIDEOs are always converted  
to 48kHz/16bit.  
96kHz/24bit All types of signals including  
96kHz/24bit are output in their  
original format. However, if the  
signal is encrypted for  
copyright protection purposes,  
the signal is only output as  
48kHz/16bit.  
b
The analog audio signals from the AUDIO OUT  
L/R jacks are not affected by this setting and keep  
their original sampling frequency level.  
31US  
 
       
Sound  
Additional Information  
There is no sound.  
, Re-connect the connecting cable securely.  
, The connecting cable is damaged.  
, The player is connected to the wrong input  
jack on the audio component (page 9, 10).  
, The audio component input is not correctly  
set.  
, The player is in pause mode or in Slow-  
motion Play mode.  
, The player is in fast forward or fast reverse  
mode.  
Troubleshooting  
If you experience any of the following  
difficulties while using the player, use this  
troubleshooting guide to help remedy the  
problem before requesting repairs. Should  
any problem persist, consult your nearest  
Sony dealer.  
, If the audio signal does not come through  
the DIGITAL OUT (COAXIAL) jack,  
check the audio settings (page 30).  
, While playing a Super VCD on which the  
audio track 2 is not recorded, no sound will  
come out when you select “2:STEREO,”  
“2:1/L,” or “2:2/R.” Press AUDIO to select  
the recorded track.  
Power  
The power is not turned on.  
, Check that the power cord is connected  
securely.  
Picture  
There is no picture/picture noise appears.  
, Re-connect the connecting cable securely.  
, The connecting cables are damaged.  
, Check the connection to your TV (page 9)  
and switch the input selector on your TV so  
that the signal from the player appears on  
the TV screen.  
The sound volume is low.  
, The sound volume is low on some DVDs.  
The sound volume may improve if you set  
“AUDIO DRC” in “AUDIO SETUP” to  
“TV MODE” (page 30).  
Operation  
, The disc is dirty or flawed.  
, You set the “PROGRESSIVE  
(COMPONENT OUT ONLY)” to “ON” in  
“SCREEN SETUP” (page 28) even though  
your TV cannot accept the progressive  
signal. In this case, refer to page 28 to reset  
the setting.  
The remote does not function.  
, The batteries in the remote are weak.  
, There are obstacles between the remote and  
the player.  
, The distance between the remote and the  
player is too far.  
, Even if your TV is compatible with  
progressive format 480p signals and  
connected using COMPONENT VIDEO  
OUT jacks, the image may be affected when  
you set the player to progressive format. In  
this case, set the “PROGRESSIVE  
(COMPONENT OUT ONLY)” in  
“SCREEN SETUP” to “OFF” (page 28) so  
that the player is set to normal (interlace)  
format.  
, The remote is not pointed at the remote  
sensor on the player.  
The disc does not play.  
, The disc is turned over.  
Insert the disc with the playback side facing  
down.  
, The disc is skewed.  
, The player cannot play certain discs  
, The region code on the DVD does not match  
the player.  
, Moisture has condensed inside the player  
(page 3).  
, The player cannot play a recorded disc that  
is not correctly finalized (page 35).  
32US  
 
     
The MP3 audio track cannot be played  
, The player cannot play audio tracks in  
mp3PRO format.  
, “MODE (MP3, JPEG)” is set to “IMAGE  
(JPEG)” (page 18).  
Some functions such as Stop, Fast Play,  
Slow Play, Slow-motion Play, Repeat  
Play, Shuffle Play, or Program Play cannot  
be performed.  
, Depending on the disc, you may not be able  
to do some of the operations above.  
The JPEG image file cannot be played  
The player does not operate properly.  
, When static electricity, etc., causes the  
player to operate abnormally, unplug the  
player.  
, The image is larger than 3072 (width) ×  
2048 (height) in normal mode, or more than  
3,300,000 pixels in progressive JPEG.  
(Some progressive JPEG files cannot be  
displayed even if the file size is within this  
specified capacity.)  
5 numbers or letters are displayed on the  
screen.  
, The self-diagnosis function was activated.  
, “MODE (MP3, JPEG)” is set to “AUDIO  
The disc tray does not open and “  
(LOCKED) appears on the front panel  
display.  
The MP3 audio tracks and JPEG image  
files start playing simultaneously.  
, “MODE (MP3, JPEG)” is set to “AUTO”  
, Child Lock is set (page 15).  
The album/track/file names are not  
displayed correctly.  
, The player can only display numbers and  
alphabet. Other characters are displayed as  
The disc tray does not open and  
” (TRAY LOCKED) appears on  
the front panel display.  
, Contact your Sony dealer or local  
authorized Sony service facility.  
“ .”  
*
The disc does not start playing from the  
“Data error” appears on the TV screen  
when playing a DATA disc.  
, The MP3 audio track/JPEG image file you  
want to play is broken.  
, The data is not MPEG-1 Audio Layer III  
data.  
, The JPEG image file format does not  
conform to DCF (page 34).  
beginning.  
, Program Play, Shuffle Play, Repeat Play, or  
A-B Repeat Play is selected (page 19).  
, Resume play has taken effect (page 14).  
“Copyright lock” appears and the screen  
turns blue when playing in DVD-VR mode.  
, Images taken from digital broadcasts, etc.,  
may contain copy protection signals, such  
as complete copy protection signals, single  
copy signals, and restriction-free signals.  
When images that contain copy protection  
signals are played, a blue screen may appear  
instead of the images. It may take a while  
when looking for playable images. (For  
player that cannot play images that contain  
a copy protection only)  
, The JPEG image file has the extension  
“.JPG” or “.JPEG,” but is not in JPEG  
format.  
33US  
 
The player can play recordable media that is  
correctly finalized.  
“DVD+RW,” “DVD-RW,” “DVD+R,”  
“DVD+R DL,” “DVD-R,” “DVD VIDEO,”  
and “CD” logos are trademarks.  
Self-diagnosis Function  
(When letters/numbers appear on the  
screen)  
The player cannot play the discs other than  
above. Also, the player cannot play the  
following discs:  
• A disc recorded in a color system other than  
NTSC, such as PAL or SECAM (this player  
conforms to the NTSC color system).  
• A disc that has a non-standard shape (e.g.,  
card, heart).  
When the self-diagnosis function is activated  
to prevent the player from malfunctioning, a  
five-character service number (e.g., C 13 50)  
with a combination of a letter and four digits  
appears on the screen. In this case, check the  
following table.  
First three  
characters of action  
the service  
Cause and/or corrective  
• A disc with paper or stickers on it.  
• A disc that has the adhesive of cellophane  
tape or a sticker still left on it.  
number  
C 13  
The disc is dirty or recorded  
Note about CDs/DVDs  
The player can play CD-ROMs/CD-Rs/CD-  
RWs recorded in the following formats:  
– music CD format  
in a format that this player  
cannot play (page 34).  
,Clean the disc with a  
cleaning cloth or check its  
format.  
– video CD format  
– MP3 audio tracks and JPEG image files of  
format conforming to ISO 9660* Level 1/  
Level 2, or its extended format, Joliet  
– KODAK Picture CD format  
C 31  
The disc is not inserted  
correctly.  
,Re-insert the disc  
correctly.  
* A logical format of files and folders on CD-  
ROMs, defined by ISO (International  
Organization for Standardization).  
Playable Discs  
The player can play DVD-ROMs/  
DVD+RWs/DVD+Rs/DVD+R DLs/  
DVD-RWs/DVD-Rs/DVD-R DLs recorded  
in the following formats:  
Format of discs  
Commercial DVD  
– MP3 audio tracks and JPEG image files of  
format conforming to UDF (Universal Disk  
Format).  
DVD-RW/-R  
MP3 audio track or JPEG image  
file that the player can play  
DVD+RW/+R/  
+R DL  
The player can play the following tracks and  
files:  
– MP3 audio tracks with the extension  
“.MP3.”  
– JPEG image files with the extension  
“.JPEG” or “.JPG.”  
– JPEG image files that conform to the DCF*  
image file format.  
VIDEO CD/  
Music CD  
* “Design rule for Camera File system”: Image  
standards for digital cameras regulated by JEITA  
(Japan Electronics and Information Technology  
Industries Association).  
CD-RW/-R  
34US  
 
         
z
Region code  
• If you add numbers (01, 02, 03, etc.) to the front  
of the track/file names when you store the tracks  
(or files) in a disc, the tracks and files will be  
played in that order.  
• Since a disc with a complex hierarchy of folders  
takes longer to start playback, it is recommended  
that you create albums with no more than two  
hierarchies.  
Your player has a region code printed at the  
bottom of the unit and only will play  
commercial DVDs (playback only) labeled  
with identical region codes. This system is  
used to protect copyrights.  
• To repeat both MP3 audio tracks and JPEG image  
files in a single album, repeat the same MP3 audio  
track or album when “MODE (MP3, JPEG)” is set  
to “AUTO.” See “Playing repeatedly (Repeat  
Play)” (page 21) to repeat the track or album.  
ALL  
Commercial DVDs labeled  
play on this player.  
will also  
Depending on the commercial DVD, there  
may be no region code indication, even  
though playing the commercial DVD is  
prohibited by area restrictions.  
b
• The player will play any data with the extension  
“.MP3,” “.JPG,” or “.JPEG,” even if they are not  
in MP3 or JPEG format. Playing these data may  
generate a loud noise which could damage your  
speaker system.  
DVP–XXXX  
X
Region code  
00V 00Hz  
NO.  
00W  
0-000-000-00  
• The player does not conform to audio tracks in  
mp3PRO format.  
• Some JPEG files cannot be played.  
b
• Notes about recordable media  
• You can view a slide show with sound only when  
the MP3 audio tracks and JPEG image files are  
placed in the same album.  
• If playing time of JPEG image or MP3 audio is  
longer than the other, the longer one continues  
without sound or image.  
Some recordable media cannot be played on this  
player due to the recording quality or physical  
condition of the disc, or the characteristics of the  
recording device and authoring software.  
The disc will not play if it has not been correctly  
finalized. For more information, refer to the  
operating instructions for the recording device.  
Note that some playback functions may not work  
with some DVD+RWs/DVD+Rs/DVD+R DLs,  
even if they have been correctly finalized. In this  
case, view the disc by normal playback. Also  
some DATA discs created in Packet Write format  
cannot be played.  
• If you play large MP3 track data and JPEG image  
data at the same time, the sound may skip. It is  
recommended that you set the MP3 bit rate to 128  
kbps or lower when creating the file. If the sound  
still skips, then reduce the size of the JPEG file.  
• Some JPEG files, especially progressive JPEG  
files or JPEG files of 3,000,000 pixels or more,  
may take longer to display than others, which may  
make the duration seem longer than the setting  
you selected.  
• The player recognizes a maximum of 200 albums  
regardless of the selected mode. Of each album,  
the player recognizes up to 300 MP3 audio tracks  
and 300 JPEG image files when “AUTO” is  
selected, 600 MP3 audio tracks when “AUDIO  
(MP3)” is selected and 600 JPEG image files  
when “IMAGE (JPEG)” is selected.  
• Music discs encoded with copyright protection  
technologies  
This product is designed to playback discs that  
conform to the Compact Disc (CD) standard.  
Various music discs encoded with copyright  
protection technologies are marketed by some  
record companies. Please be aware that among  
those discs, there are some that do not conform to  
the CD standard and may not be playable by this  
product.  
• Proceeding to the next or another album may take  
some time.  
• For player that cannot play images that  
contain a copy protection only  
Images in DVD-VR mode with CPRM*  
protection may not be played if they contain a  
copy protection signal. “Copyright lock” appears  
on the screen.  
* CPRM (Content Protection for Recordable  
Media) is a coding technology that protects the  
copyright of images.  
35US  
,continued  
 
 
• Note on DualDiscs  
A DualDisc is a two sided disc product which  
mates DVD recorded material on one side with  
digital audio material on the other side.  
However, since the audio material side does not  
conform to the Compact Disc (CD) standard,  
playback on this product is not guaranteed.  
Specifications  
System  
Laser: Semiconductor laser  
Outputs  
Note on playback operations of  
DVDs and VIDEO CDs  
(Jack name: Jack type/Output level/Load  
impedance)  
AUDIO OUT:  
Some playback operations of DVDs and  
VIDEO CDs may be intentionally set by  
software producers. Since this player plays  
DVDs and VIDEO CDs according to the disc  
contents the software producers designed,  
some playback features may not be available.  
Also, refer to the instructions supplied with  
the DVDs or VIDEO CDs.  
Phono jack/2 Vrms/10 kilohms  
DIGITAL OUT (COAXIAL):  
Phono jack/0.5 Vp-p/75 ohms  
COMPONENT VIDEO OUT(Y, PB, PR):  
Phono jack/Y: 1.0 Vp-p/PB, PR  
:
1
interlace* = 0.648 Vp-p,  
2
progressive or interlace* = 0.7 Vp-p/75  
ohms  
1
2
*
*
BLACK LEVEL (COMPONENT OUT) is ON  
BLACK LEVEL (COMPONENT OUT) is OFF  
Copyrights  
VIDEO OUT:  
Phono jack/1.0 Vp-p/75 ohms  
This product incorporates copyright  
protection technology that is protected by  
U.S. patents and other intellectual property  
rights. Use of this copyright protection  
technology must be authorized by  
Macrovision, and is intended for home and  
other limited viewing uses only unless  
otherwise authorized by Macrovision.  
Reverse engineering or disassembly is  
prohibited.  
General  
Power requirements:  
U.S. models: 120 V AC, 60 Hz  
Models for other areas: 110-240 V AC,  
50/60 Hz  
See page 3 for further information.  
Power consumption: 10 W  
Dimensions (approx.):  
320 × 32 × 209 mm (12 5/8 × 1 5/6  
×
8 1/4 in.) (width/height/depth) incl.  
projecting parts  
Mass (approx.): 1.2 kg (2 lb 11 oz)  
Operating temperature: 5 °C to 35 °C  
(41 °F to 95 °F)  
Operating humidity: 25 % to 80 %  
Supplied accessories  
• Audio/video cable (phono plug × 3 y  
phono plug × 3) (1)  
• Remote commander (remote) (1)  
• Size AA (R6) batteries (2)  
A plug adaptor is included with some models.  
Specifications and design are subject to  
change without notice.  
36US  
 
   
Language Code List  
For details, see pages 6, 26.  
The language spellings conform to the ISO 639: 1988 (E/F) standard.  
Code Language  
Code Language  
Code Language  
Code Language  
1027 Afar  
1183 Irish  
1347 Maori  
1507 Samoan  
1508 Shona  
1509 Somali  
1511 Albanian  
1512 Serbian  
1513 Siswati  
1514 Sesotho  
1515 Sundanese  
1516 Swedish  
1517 Swahili  
1521 Tamil  
1028 Abkhazian  
1032 Afrikaans  
1039 Amharic  
1044 Arabic  
1045 Assamese  
1051 Aymara  
1052 Azerbaijani  
1053 Bashkir  
1057 Byelorussian  
1059 Bulgarian  
1060 Bihari  
1186 Scots Gaelic  
1194 Galician  
1196 Guarani  
1203 Gujarati  
1209 Hausa  
1349 Macedonian  
1350 Malayalam  
1352 Mongolian  
1353 Moldavian  
1356 Marathi  
1357 Malay  
1217 Hindi  
1226 Croatian  
1229 Hungarian  
1233 Armenian  
1235 Interlingua  
1239 Interlingue  
1245 Inupiak  
1248 Indonesian  
1253 Icelandic  
1254 Italian  
1358 Maltese  
1363 Burmese  
1365 Nauru  
1369 Nepali  
1376 Dutch  
1379 Norwegian  
1393 Occitan  
1403 (Afan)Oromo  
1408 Oriya  
1417 Punjabi  
1428 Polish  
1435 Pashto;  
Pushto  
1436 Portuguese  
1463 Quechua  
1481 Rhaeto-  
Romance  
1482 Kirundi  
1483 Romanian  
1489 Russian  
1491 Kinyarwanda  
1495 Sanskrit  
1498 Sindhi  
1501 Sangho  
1502 Serbo-  
Croatian  
1525 Telugu  
1527 Tajik  
1528 Thai  
1061 Bislama  
1066 Bengali;  
Bangla  
1067 Tibetan  
1070 Breton  
1079 Catalan  
1093 Corsican  
1097 Czech  
1103 Welsh  
1105 Danish  
1109 German  
1130 Bhutani  
1142 Greek  
1144 English  
1145 Esperanto  
1149 Spanish  
1150 Estonian  
1151 Basque  
1157 Persian  
1165 Finnish  
1166 Fiji  
1529 Tigrinya  
1531 Turkmen  
1532 Tagalog  
1534 Setswana  
1535 Tonga  
1538 Turkish  
1539 Tsonga  
1540 Tatar  
1257 Hebrew  
1261 Japanese  
1269 Yiddish  
1283 Javanese  
1287 Georgian  
1297 Kazakh  
1298 Greenlandic  
1299 Cambodian  
1300 Kannada  
1301 Korean  
1305 Kashmiri  
1307 Kurdish  
1311 Kirghiz  
1543 Twi  
1557 Ukrainian  
1564 Urdu  
1572 Uzbek  
1581 Vietnamese  
1587 Volapük  
1613 Wolof  
1632 Xhosa  
1665 Yoruba  
1684 Chinese  
1697 Zulu  
1313 Latin  
1326 Lingala  
1327 Laothian  
1332 Lithuanian  
1334 Latvian;  
Lettish  
1171 Faroese  
1174 French  
1181 Frisian  
1503 Singhalese  
1505 Slovak  
1506 Slovenian  
1345 Malagasy  
1703 Not specified  
Parental Control Area Code List  
For details, see page 22.  
Code Area  
Code Area  
Code Area  
Code Area  
2044 Argentina  
2047 Australia  
2046 Austria  
2057 Belgium  
2070 Brazil  
2079 Canada  
2090 Chile  
2165 Finland  
2174 France  
2109 Germany  
2248 India  
2238 Indonesia  
2254 Italy  
2276 Japan  
2304 Korea  
2363 Malaysia  
2362 Mexico  
2149 Spain  
2376 Netherlands  
2390 New Zealand  
2379 Norway  
2499 Sweden  
2086 Switzerland  
2528 Thailand  
2184 United  
Kingdom  
2427 Pakistan  
2424 Philippines  
2436 Portugal  
2489 Russia  
2092 China  
2115 Denmark  
2501 Singapore  
37US  
 
       
Index  
Numerics  
F
S
H
A
I
J
T
L
M
B
BLACK LEVEL  
V
C
O
Z
P
Continuous play  
PROGRESSIVE  
ONLY) 28  
D
Q
R
E
38US  
 
 
Conexiones  
Al desembalar la unidad, compruebe los accesorios suministrados que se detallan en  
“Specifications” del Manual de instrucciones en inglés.  
b
• Enchufe los cables firmemente para evitar ruidos no deseados.  
• Consulte el manual de instrucciones suministrado con los componentes que va a conectar.  
• Asegúrese de desconectar el cable de corriente de cada componente antes de realizar las conexiones.  
Paso 1: Conexión del televisor  
Conecte este reproductor al monitor del televisor mediante un cable de video. Seleccione el  
patrón A o B, de acuerdo con la toma de entrada del monitor, proyector o componente de  
audio.  
INPUT  
L
(blanco)  
Cable de audio/video  
(suministrado)  
A
AUDIO  
(rojo)  
R
(amarillo)  
VIDEO  
(amarillo)  
(rojo)  
(blanco)  
Televisor  
a VIDEO OUT  
(salida video)  
a AUDIO OUT (salida audio)  
P
B
VIDEO  
L
DIGITAL  
OUT  
VIDEO OUT  
COMPONENT  
VIDEO OUT  
R
Y
P
R
COAXIAL  
AUDIO OUT  
Reproductor de CD/DVD  
a COMPONENT VIDEO  
OUT (salida de video del  
componente)  
(verde)  
(rojo)  
(azul)  
COMPONENT  
VIDEO IN  
B
Y
(verde)  
Cable de video  
PB  
componente  
(azul)  
PR  
(no suministrado)  
(rojo)  
Televisor  
: Flujo de señal  
b
A Tomas de entrada de audio/  
video  
Conecte el cable de audio suministrado a las tomas  
de entrada de audio (I/D) del televisor.  
Disfrutará de imágenes de calidad estándar.  
Si lo conecta a un televisor de pantalla  
panorámica  
B Tomas de entrada de video  
Según el disco, es posible que la imagen no  
quepa en la pantalla del televisor. Para  
cambiar la relación de aspecto, consulte la  
versión en inglés del Manual de  
instrucciones.  
componente (Y, PB, PR  
)
Este tipo de conexiones proporciona  
imágenes de alta calidad con una  
reproducción fiel de los colores.  
2ES  
 
   
b
b
No conecte una videograbadora, etc., entre el televisor  
y el reproductor. Si pasa las señales del reproductor a  
través de la videograbadora, es posible que no reciba  
una imagen clara en la pantalla del televisor. Si el  
televisor sólo tiene una toma de entrada de audio/  
video, conecte el reproductor a esta toma.  
• Tras completar la conexión, realice los ajustes  
apropiados en Ajuste rápido (página 6). De lo  
contrario, los altavoces no emitirán el sonido o  
bien emitirán un ruido fuerte.  
• Los efectos TVS de este reproductor no son  
compatibles con esta conexión.  
• Para escuchar pistas de sonido DTS, debe utilizar  
esta conexión. Las pistas de sonido DTS no se  
emiten a través de las tomas AUDIO OUT L/R  
aunque ajuste “DTS” en “SI” en Ajuste rápido  
Para conectar el componente de audio  
Utilice el siguiente patrón.  
Reproductor de CD/DVD  
PB  
VIDEO  
L
DIGITAL  
OUT  
VIDEO OUT  
COMPONENT  
VIDEO OUT  
R
Y
PR  
COAXIAL  
AUDIO OUT  
a DIGITAL OUT (COAXIAL)  
(salida digital coaxial)  
DIGITAL  
OUT  
COAXIAL  
Cable digital coaxial (no  
suministrado)  
a la entrada  
digital coaxial  
Componente de audio que  
dispone de un codificador  
: Flujo de señal  
z
Para la colocación correcta de los altavoces,  
consulte el manual de instrucciones suministrado  
con los componentes conectados.  
Si el componente de audio dispone de  
1
2
decodificador Dolby* Digital o DTS* y una  
toma de entrada digital, utilice esta conexión.  
Podrá disfrutar de los efectos de sonido  
envolvente de Dolby Digital (5.1ch) y DTS  
(5.1ch).  
*1  
Fabricado bajo licencia de Dolby Laboratories.  
Dolby, Pro Logic y el símbolo de la doble D son  
marcas comerciales de Dolby Laboratories.  
Fabricado bajo licencia según Patente de los  
*2  
EE.UU. N° 5.451.942 y otras patentes emitidas y  
pendientes en los EE.UU. y el resto del mundo.  
DTS y DTS Digital Out son marcas registradas,  
y los logos y símbolo de DTS son marcas  
comerciales de DTS, Inc. © 1996-2007 DTS,  
Inc. Reservados todos los derechos.  
3ES  
 
Control del televisor mediante el  
control remoto  
Puede controlar el nivel del sonido, la fuente  
de entrada y el interruptor de alimentación del  
televisor Sony con el control remoto  
suministrado.  
Paso 2: Conexión del  
cable de alimentación  
Conecte los cables de alimentación del  
reproductor y del televisor a una toma de ca.  
TV INPUT  
(selección  
de entrada)  
TV (televisor)  
TV  
PICTURE  
NAVI  
Paso 3: Preparación del  
control remoto  
VOL (volumen)  
+/–  
Botones  
numéricos  
TIME/TEXT  
CLEAR  
AUDIO SUBTITLE  
MENU  
TOP MENU  
Se puede controlar el reproductor con el  
control remoto suministrado. Inserte dos pilas  
tamaño AA (R6) de forma que coincidan sus  
extremos 3 y # con las marcas del interior  
del compartimiento. Al utilizar el control  
remoto, oriéntelo hacia el sensor remoto  
del reproductor.  
RETURN  
DISPLAY  
Puede controlar el televisor mediante los  
botones que se indican a continuación.  
Presionando  
Puede  
TV [/1  
Encender o apagar el  
televisor  
VOL  
(volumen) +/–  
Ajustar el volumen del  
televisor  
TV INPUT  
(selección de  
entrada)  
Cambiar la fuente de entrada  
del televisor entre éste y otras  
fuentes de entrada  
b
• No deje el control remoto en lugares  
extremadamente cálidos o húmedos.  
• No permita que caigan objetos extraños sobre el  
control remoto, especialmente cuando sustituya  
las pilas.  
b
Según la unidad conectada, podrá controlar el  
televisor utilizando algunos o todos los botones del  
control remoto suministrado.  
• No exponga el sensor del control remoto a la luz  
directa del sol ni a dispositivos de iluminación. Si  
lo hace, pueden producirse fallas en el  
funcionamiento.  
• Cuando no vaya a usar el control remoto durante  
un tiempo prolongado, extraiga las pilas para  
evitar posibles daños por fugas y corrosión.  
4ES  
 
   
Para controlar otros televisores con el  
control remoto  
También puede controlar el nivel del sonido,  
la fuente de entrada y el interruptor de  
alimentación de un televisor de otro  
proveedor con el control remoto  
suministrado.  
Si el televisor figura en la tabla que aparece a  
continuación, establezca el código del  
fabricante correspondiente.  
1
Mientras mantiene presionado TV [/1,  
presione los botones numéricos para  
seleccionar el código del fabricante del  
televisor (consulte la tabla que se  
proporciona a continuación).  
2
Suelte TV [/1.  
Códigos de televisores controlables  
Si aparece más de un código, ingréselos uno  
tras otro hasta encontrar el que funciona con  
su televisor.  
Fabricante  
Sony  
Número de código  
01 (predeterminado)  
02  
Hitachi  
LG/Goldstar/NEC 04  
MGA/Mitsubishi 13  
Panasonic  
Philips  
Pioneer  
RCA  
19  
21  
16  
10  
20  
18  
07  
Samsung  
Sharp  
Toshiba  
b
• Al sustituir las pilas del control remoto, es posible  
que el código recupere el valor de fábrica. Vuelva  
a ajustar el código apropiado.  
• Según la unidad que conecte, podrá controlar el  
televisor utilizando algunos o todos los botones  
del control remoto suministrado.  
5ES  
 
Paso 4: Ajuste rápido  
Siga los pasos siguientes para realizar el mínimo de ajustes básicos para utilizar el reproductor.  
Para saltar un ajuste, presione >. Para volver al ajuste anterior, presione ..  
TV  
PICTURE  
NAVI  
TV  
INPUT  
TIME/TEXT  
CLEAR  
AUDIO SUBTITLE  
MENU  
TOP MENU  
ENTER  
(ingresar)  
RETURN  
DISPLAY  
1
2
Encienda el televisor.  
LANGUAGE SETUP  
OSD:  
ENGLISH  
ENGLISH  
MENU:  
Presione [/1.  
El reproductor se enciende.  
FRENCH  
AUDIO:  
SUBTITLE:  
SPANISH  
PORTUGUESE  
3
Cambie el selector de entrada del  
televisor para que la señal del  
reproductor aparezca en la  
pantalla del televisor.  
5
6
Presione X/x para seleccionar un  
idioma.  
El reproductor muestra el menú y los  
subtítulos en el idioma seleccionado.  
En la parte inferior de la pantalla,  
aparecerá “Press [ENTER] to run  
QUICK SETUP” (Toque [ENTER] para  
AJUSTE RÁPIDO). Si este mensaje no  
aparece, seleccione “QUICK”  
(RÁPIDO) en “SETUP” (AJUSTE) del  
menú de control para ejecutar el ajuste  
rápido.  
Presione ENTER.  
Aparece la pantalla de ajustes que le  
permitirá seleccionar la relación de  
aspecto del televisor que vaya a conectar.  
AJUSTE PANTALLA  
4:3 LETTER BOX  
4:3 LETTER BOX  
4:3 PAN SCAN  
16:9  
TIPO TV:  
4
Presione ENTER sin insertar  
ningún disco.  
PROTECTOR PANTALLA:  
FONDO:  
NIVEL NEGRO DE SEÑAL:  
NIVEL NEGRO DE SEÑAL (COMPONENT OUT):  
PROGRESSIVE (COMPONENT OUT ONLY):  
MODALIDAD (PROGRESSIVE):  
NO  
Aparece la pantalla de ajustes que le  
permitirá seleccionar el idioma utilizado  
en la pantalla.  
NO  
AUTO  
SALIDA 4:3:  
COMPLETO  
6ES  
 
 
7
8
Presione X/x para seleccionar el  
ajuste que coincida con el tipo de  
televisor.  
10Presione X/x para seleccionar el  
tipo de señal Dolby Digital que  
desee enviar al componente de  
audio.  
Si tiene un televisor 4:3 estándar  
• 4:3 LETTER BOX (tipo buzón) o 4:3  
PAN SCAN (exploración PAN)  
Si el componente de audio dispone de  
decodificador Dolby Digital, seleccione  
“DOLBY DIGITAL”. De lo contrario,  
seleccione “D-PCM”.  
Si tiene un televisor con pantalla  
panorámica o uno 4:3 estándar con el  
modo de pantalla panorámica  
• 16:9  
AJUSTE AUDIO  
AUDIO DRC:  
MEZCLA:  
ESTANDAR  
DOLBY SURROUND  
SI  
SALIDA DIGITAL:  
DOLBY DIGITAL:  
DTS:  
Presione ENTER.  
DOLBY DIGITAL  
DOLBY DIGITAL  
D-PCM  
Aparece la pantalla de ajustes que le  
permitirá seleccionar el tipo de toma  
utilizada para conectar su componente de  
audio, tal como un amplificador  
(receptor).  
48kHz/96kHz PCM:  
11Presione ENTER.  
¿DVD conectado a receptor-amp? Elija  
tipo de toma utilizado.  
Se selecciona “DTS”.  
AJUSTE AUDIO  
AUDIO DRC:  
SI  
ESTANDAR  
AUDIO OUTPUT L/R  
MEZCLA:  
DOLBY SURROUND  
DIGITAL OUTPUT  
SALIDA DIGITAL:  
DOLBY DIGITAL:  
DTS:  
SI  
NO  
DOLBY DIGITAL  
NO  
NO  
SI  
48kHz/96kHz PCM:  
9
Presione X/x para seleccionar  
(si existe) el tipo de toma que  
utilice para conectar a un  
12Presione X/x para seleccionar si  
desea o no enviar una señal DTS  
al componente de audio.  
componente de audio y, a  
continuación, presione ENTER.  
Si no conectó el componente de audio,  
seleccione “NO” y vaya al paso 13.  
Si conectó el componente de audio sólo  
con un cable de audio, seleccione “SI:  
AUDIO OUTPUT L/R” y vaya al paso  
13.  
Si conectó un componente de audio  
mediante un cable digital coaxial,  
seleccione “SI: DIGITAL OUTPUT”.  
Si el componente de audio dispone de  
decodificador DTS, seleccione “SI”. De  
lo contrario, seleccione “NO”.  
13Presione ENTER.  
El ajuste rápido ha finalizado y  
conexiones han completado.  
7ES  
 
Para detener la reproducción  
Presione x.  
Reproducción  
Para introducir una pausa en la  
reproducción  
Presione X.  
Reproducción de discos  
z
El reproductor se puede apagar en forma automática  
siempre que lo deje en modo de parada durante más  
de 30 minutos. Para activar o desactivar esta  
función, ajuste “DESCONEXION  
AUTOMATICA” en “AJUSTE  
Algunas operaciones pueden ser distintas o  
estar limitadas en función del DVD o VIDEO  
CD.  
Consulte las instrucciones de uso  
suministradas con el disco.  
PERSONALIZADO” en “SI” o “NO”.  
TV  
INPUT  
TV  
PICTURE  
NAVI  
b
Los discos creados con grabadoras de DVD deberán  
estar finalizados correctamente para poder  
reproducirse. Para obtener más información acerca  
de la finalización, consulte el manual de  
instrucciones suministrado con la grabadora de  
DVD.  
Botones  
numéricos  
TIME/TEXT  
CLEAR  
AUDIO SUBTITLE  
MENU  
TOP MENU  
ENTER  
(ingresar)  
Notas sobre la reproducción de pistas de  
sonido DTS de un DVD VIDEO  
Las señales de audio DTS se emiten sólo a  
través de la toma DIGITAL OUT  
(COAXIAL).  
RETURN  
(volver)  
RETURN  
DISPLAY  
Reanudación de la reproducción a partir  
del punto en el que se detuvo el disco  
(Reanudación multidisco)  
Si vuelve a presionar N después de detener  
la reproducción, el reproductor iniciará la  
reproducción a partir del punto en el que la  
detuvo al presionar x.  
1
Presione Z en el reproductor y  
coloque un disco en la bandeja de  
discos.  
z
• Para reproducir el disco desde el principio,  
presione x dos veces y, a continuación, presione  
N.  
• Con discos DVD VIDEO y VIDEO CD, el  
reproductor memoriza el punto en el que se  
detuvo el disco hasta un máximo de 6 discos y  
reanuda la reproducción la próxima vez que  
inserte el mismo disco. Si memoriza un punto de  
reanudación de reproducción para el disco  
número 7, el punto de reanudación de  
reproducción del primer disco se borrará.  
Con la cara de  
reproducción hacia abajo  
2
Presione N.  
La bandeja de discos se cierra y el  
reproductor inicia la reproducción  
(continua). Ajuste el volumen en el  
televisor o en el componente de audio.  
De acuerdo con el disco, puede aparecer  
un menú en la pantalla del televisor.  
b
• Para que esta opción funcione, se debe ajustar  
“REANUDACION MULTIDISCO” de  
“AJUSTE PERSONALIZADO” en “SI”  
(predeterminado).  
• La reanudación de reproducción no funciona  
durante la reproducción aleatoria ni la  
reproducción de programa.  
8ES  
 
   
• Es posible que en algunos discos la función de  
reanudación de la reproducción no funcione,  
dependiendo del punto en el que la haya detenido,  
o si presiona [/1.  
b
Aunque seleccione “RESTAURAR” en “AJUSTE”  
del menú de control, la bandeja de discos  
permanece bloqueada.  
Reproducción de VIDEO CD con funciones  
PBC (Reproducción PBC)  
La reproducción PBC (Playback Control  
(control de reproducción)) permite reproducir  
discos VIDEO CD en forma interactiva si  
sigue las instrucciones del menú que aparece  
en la pantalla del televisor.  
Al reproducir un VIDEO CD con funciones  
PBC, aparecerá el menú en la pantalla.  
Seleccione un elemento con los botones de  
números y presione ENTER. Luego, siga las  
instrucciones del menú para las funciones  
interactivas (presione N cuando aparezca  
“Presione SELECT”).  
Consulte las instrucciones suministradas con  
el disco, ya que el procedimiento de  
operación puede variar en función del  
VIDEO CD.  
Para volver al menú  
Presione O RETURN.  
z
Para reproducir sin la opción PBC, presione ./  
> o los botones numéricos mientras el  
reproductor está detenido para seleccionar una pista  
y, a continuación, presione N o ENTER.  
En la pantalla del televisor aparece “Reproducción  
sin PBC” y el reproductor inicia la reproducción  
continua. No puede reproducir imágenes fijas,  
como un menú.  
Para regresar a la reproducción con PBC, presione  
x dos veces y, a continuación, presione N.  
Bloqueo de la bandeja de discos (Bloqueo  
para niños)  
Es posible bloquear la bandeja de discos para  
evitar que los niños la abran.  
Si el reproductor está en modo de espera,  
presione O RETURN, ENTER y, a  
continuación, \/1 en el control remoto.  
El reproductor se enciende y aparece “  
(LOCKED) (bloqueado) en la pantalla del  
panel frontal. El botón Z del reproductor no  
funcionará mientras esté activado el bloqueo  
para niños.  
Para desbloquear la bandeja de discos,  
presione O RETURN, ENTER y, a  
continuación, \/1 de nuevo cuando el  
reproductor está en modo de espera.  
9ES  
 
4-115-660-11(1)  
Sony Corporation Printed in China  
 

Sharp Projector XG P25X User Manual
Sherwood Stereo System RX 4105 User Manual
Shindaiwa Edger 81604 User Manual
Sony Car Stereo System CDX GT500 User Manual
Sony Ericsson Cell Phone Z550 User Manual
Sony Laptop PCG FX215 User Manual
Speco Technologies Security Camera CVC 870EX User Manual
StarTechcom Switch SV215MICUSBA User Manual
StreamLight Home Safety Product 700025 User Manual
Sylvania DVD VCR Combo SSD800 User Manual