No sound comes through the
headphones.
• The headphones plug is not firmly
connected.
To lo ck t h e co n t ro ls E
On ch a rg in g
Fo r t h e cu st o m e rs in t h e U.S.A. a n d
Ca n a d a
zVa rio u s w a ys o f
zPo w e r so u rce s
3-860-459-11(1)
To prevent the buttons from being
accidentally operated when you carry the
player, use this function.
•
•
Be sure to use the supplied battery charger.
Charging time may vary depending on the
battery condition.
p la yb a ck
DISPOSAL OF NICKEL METAL HYDRIDE
BATTERY.
Wh e n t o re p la ce o r ch a rg e
t h e b a t t e rie s
b
Connect the headphones plug firmly
to 2/ REMOTE jack.
Getting Started
You can operate the player on either a rechargeable battery or a dry
battery. Before using the supplied rechargeable battery for the first
time, charge it. You can also operate the player on house current (see
"Power sources").
A
Playing an MD
B
•
When you use the battery for the first time
or after a long period of disuse, the battery
life may be shorter. In this case, charge and
discharge the battery several times. The
battery life will be restored.
Pla yin g t ra cks re p e a t e d ly
C
• Volume is too low.
NICKEL METAL HYDRIDE BATTERY.
DISPOSE OF PROPERLY.
You can return your unwanted nickel
metal hydride batteries to your nearest
Sony Service Center or Factory Service
Center.
Note: In some areas the disposal of nickel
metal hydride batteries in household or
business trash may be prohibited.
For the Sony Service Center nearest you
call 1-800-222-SONY (United States only)
For the Sony Factory Service Center
nearest you call 416-499-SONY (Canada
only)
The player automatically switches to play the stereo or monaural
sound according to the recorded sound.
You can check the battery condition with the
battery indication on the remote control while
using the player.
b
Adjust the volume by pressing
VOLUME +/ – .
Po rta ble MiniDisc Player
You can play tracks repeatedly in three ways-
-all repeat, single repeat, and shuffle repeat.
• AVLS is on.
•
If the rechargeable battery capacity
becomes half the normal life, replace it with
a new one.
b
Slide AVLS to NORM.
HOLD
B
v
Used batteries
Operating instructions
Manual de instrucciones (en el reverso)
1
Play an MD.
b
v
Weak batteries. Replace all the batteries
On h e a t b u ild -u p
•
Heat may build up in the player if it is used
for an extended period of time. In this case,
leave the player to cool down.
Sp e cifica t io n s
n
The batteries have gone out.“LoBATT”
flashes in the display, and the power goes
off.
1 Press (.
Syst e m
Audio playing system
MiniDisc digital audio system
Laser diode properties
Material: GaAlAs
The player starts to play the first
track. If you use the remote control,
1
Charge the rechargeable battery.
On in st a lla t io n
HOLD
a short beep sounds in the
headphones.
to 2/REMOTE
Install the supplied rechargeable battery NH-9WM to the
supplied battery charger with correct polarity, and connect to a
wall outlet.
•
Never use the player where it will be
subjected to extremes of light, temperature,
moisture or vibration.
Battery life*
Slide HOLD in the direction of the c.
On the player, slide HOLD to lock the
controls of the player.
Caution: Do not handle damaged or
leaking nickel metal hydride battery.
PLAY MODE
Wavelength: l = 790 nm
Batteries
Playback
MZ-EP11
Press PLAY MODE on the remote control
while the player is playing an MD.
Each time you press PLAY MODE, the play
mode indication changes as follows.
Emission duration: continuous
Laser output: less than 44.6 µW*
* This output is the value measured at a distance
of 200 mm from the objective lens surface on
the optical pick-up block with 7mm aperture.
Revolutions
400 rpm to 900 rpm (CLV)
Error correction
Advanced Cross Interleave Reed Solomon Code
(ACIRC)
Sampling frequency
44.1 kHz
Coding
Adaptive TRansform Acoustic Coding (ATRAC)
Modulation system
EFM (Eight to Fourteen Modulation)
Number of channels
2 stereo channels
1 monaural channel
•
Never wrap the player in anything when it
is being used with the AC power adaptor.
Heat build-up in the player may cause
malfunction or injury.
Ni-MH
Approx. 4 hours
If you have any questions or problems
concerning your player, please consult your
nearest Sony dealer.
Headphones with remote
control (supplied)
The charger lamp goes off when the charging has finished.
Sony Corporation ©1997 Printed in Japan
To e m p h a size b a ss (DIGITAL MEGA
BASS) F
The DIGITAL MEGA BASS function
intensifies low frequency sound for richer
quality audio reproduction.
rechargeable
battery (NH-9WM (N))
• U.S.A., Canadian, European &
Australian model (Full
• Other countries & World model
(Full charging takes 120 minutes.)
One LR6 (size AA)
alkaline battery
Approx. 5 hours
On t h e h e a d p h o n e s
Road safety
VOLUME +/–
charging takes 60 minutes.)
Ow n e r' s Re co rd
Do not use headphones while driving, cycling, or
operating any motorized vehicle. It may create a
traffic hazard and is illegal in many areas. It can
also be potentially dangerous to play your player
at high volume while walking, especially at
pedestrian crossings. You should exercise
extreme caution or discontinue use in potentially
hazardous situations.
Tro u b le sh o o t in g
WARNING
The serial number is located inside the lid and
the model number is located at the bottom.
Record the serial number in the space
provided below. Refer to them whenever you
call upon your Sony dealer regarding this
product.
*
The battery life may be shorter due to
SHUF
operating conditions and the temperature of
the location.
DIGITAL MEGA BASS
To p re ve n t fire o r sh o ck
h a za rd , d o n o t e xp o se
t h e u n it t o ra in o r
m o ist u re .
Should any problem persist after you have
made these checks, consult your nearest Sony
dealer.
lamp
lamp
VOL +/–
Play mode indication
NH-9WM
(supplied)
Usin g o n h o u se cu rre n t H
The player does not w ork or w orks
poorly.
• You tried to play with no disc in the
player (“No DISC” flashes).
(none) (normal play)
All the tracks are played once.
Model No. MZ-EP11
Z
]
0
1
2
Serial No. _______________________________
2 Press VOLUME +/– (VOL +/–
1
Connect the AC-E15L AC power adaptor
(not supplied) to the DC IN 1.5V jack of
the player.
.
Preventing hearing damage
on the remote control) to
adjust the volume.
You can check the volume in the
display of the remote control.
”f” (all repeat)
All the tracks are played
repeatedly.
To st o p p la y, press p.
"MD WALKMAN" is a trademark of Sony
Corporation.
}
Avoid using headphones at high volume.
Hearing experts advise against continuous, loud
and extended play. If you experience a ringing in
your ears, reduce the volume or discontinue use.
To a vo id e le ct rica l
sh o ck, d o n o t o p e n t h e
ca b in e t . Re fe r se rvicin g
t o q u a lifie d p e rso n n e l
o n ly.
If you use the remote control, a short
b
Insert an MD.
• The player is locked.
NH-9WM
Frequency response
20 to 20,000 Hz ± 3 dB
Wow and Flutter
Below measurable limit
Outputs
beep sounds in the headphones.
(supplied)
2
Connect the AC power adaptor to a wall
outlet.
Slide DIGITAL MEGA BASS.
.
b
Slide HOLD against the arrow to
unlock the player.
Choose 1 (slight effect) or 2 (strong effect).
To cancel the effect, set DIGITAL MEGA
BASS to 0.
”f1” (single repeat)
A single track is played
repeatedly.
We lco m e !
• Moisture has condensed inside the
player.
Caring for others
Fo r m o d e ls su p p lie d w it h t h e AC p lu g a d a p t o r
If the battery charger does not fit the wall outlet,
use the AC plug adaptor.
Keep the volume at a moderate level. This will
allow you to hear outside sounds and to be
considerate of the people around you.
Headphones: stereo mini-jack, maximum output
level 5 mW + 5 mW, load impedance 16 ohm
to w all outlet
Welcome to the world of the MiniDisc! Here
are some of the capabilities and features you'll
discover with the new MiniDisc Player.
Compact MiniDisc player using a new-
designed head-loading system.
You can insert or eject an MD while the
player is in your pocket or bag.
You can operate this player by inserting
either a “chewing-gum type” rechargeable
battery or a dry battery into the battery
compartment of the player.
Using only one LR6 (size AA) dry battery
by the power saving mechanism.
The headphones with remote control
including LCD display – You can also
operate this player using the remote control
(supplied) while the player is in your
pocket.
.
b
Take the MD out and leave the
player in a warm place for several
hours until the moisture evaporates.
”f SHUF” (shuffle repeat)
All the tracks are played
repeatedly in random order.
Note
If the sound is distorted when emphasizing bass,
turn down the volume.
Ca u t io n
Ge n e ra l
Pow er requirements
Nickel metal hydride rechargeable battery NH-
9WM(N) (supplied)
One LR6 (size AA) battery (supplied with the
World model only)
Sony AC Power Adaptor AC-E15L* (not
supplied) connected at the DC IN 1.5 V jack
Battery operation time
Disp la y w in d o w w h ile p la yin g
b a ck
•
•
On t h e Min iDisc ca rt rid g e
• The rechargeable battery or dry
batteries are weak (n“LoBATT”
flashes).
The use of optical instruments with this
product will increase eye hazard.
To
Press (Beeps in the
headphones)
•
•
Do not break open the shutter.
Do not place the cartridge where it will be
subject to light, temperature, moisture or
dust.
To p ro t e ct yo u r h e a rin g (AVLS) G
The AVLS (Automatic Volume Limiter
System) function keeps down the maximum
volume to protect your ears.
2
Insert a rechargeable battery.
• Display window on the remote control
Pause
P (Continuous short
b
Replace the dry battery or recharge
the battery.
In fo rm a t io n
beeps)
Track name3) or elapsed time of
the track being played
IN NO EVENT SHALL SELLER BE LIABLE
FOR ANY DIRECT, INCIDENTAL OR
CONSEQUENTIAL DAMAGES OF ANY
NATURE, OR LOSSES OR EXPENSES
RESULTING FROM ANY DEFECTIVE
PRODUCT OR THE USE OF ANY
PRODUCT.
Insert the battery
with correct
polarity.
Slide open the battery
compartment lid like the arrow
in the illustration.
• The rechargeable battery or dry battery
have been installed incorrectly.
Tip s o n p la yb a ck
Press P again to
resume play.
On cle a n in g
• Clean the player casing with a soft cloth slightly
moistened with water or a mild detergent
solution. Do not use any type of abrasive pad,
scouring powder or solvent such as alcohol or
benzene as it may mar the finish of the casing.
• Wipe the disc cartridge with a dry cloth to
remove dirt.
• Dust on the lens may prevent the unit from
operating properly. Be sure to close the disc
compartment lid after inserting and ejecting an
MD.
b
Install the battery correctly.
to DC IN 1.5 V
AVLS
To kn o w t h e t ra ck n a m e a n d t im e D
Press DISPLAY on the remote control while
the player is playing an MD.
Each time you press DISPLAY, the display
changes as follows.
See “When to replace or charge the battery”
Dimensions
•
•
• An MD with no recording on it is
inserted (“BLANK” flashes).
=or =side of
( on the remote
control once (Three
short beeps)
Find the
Approx. 80 × 18.5 × 104 mm (w/ h/ d) (3 1/ 4×
3/ 4 × 4 1/ 8 in.) not including projecting parts and
controls
beginning of
the current
track
b
Insert a recorded MD.
Note
• The player cannot read the disc (it’s
scratched or dirty) (“ERROR” flashes).
The battery indication ı is displayed while
using the AC power adaptor.
NORM
LIMIT
Mass
Fo r Cu st o m e rs in Ca n a d a
b
Reinsert or replace the disc.
+ or + side of
( on the remote
control once (Two
short beeps)
Find the
beginning of
the next track
Approx. 160 g (5.6 oz.) the player only
Approx. 200 g (7.1 oz.) incl. a premastered MD,
and a nickel metal hydride rechargeable battery
NH-9WM
Supplied accessories
Battery Charger (1)
To prevent electric shock, do not use this
polarized AC plug with an extension cord,
receptacle or other outlet unless the blades
can be fully inserted to prevent blade
exposure.
Track number
• While operating, the player received a
mechanical shock, too much static,
abnormal power voltage caused by
lightning, etc.
1) To go backwards or forward quickly
without listening, press P and keep
pressing = or + .
2) Once you eject an MD, the point to start
play will change to the beginning of the
first track.
Set AVLS to LIMIT.
zAd d it io n a l in fo rm a t io n
The volume is kept at a moderate level, even
if you try to turn the volume above the
limited level.
keep pressing
= or =side of
( on the remote
control
Go backwards
while playing1)
b
Restart the operation as follows.
1 Disconnect all the power sources.
2 Leave the player for about 30
seconds.
No t e s o n t h e b a t t e rie s
Rechargeable battery (1)
Fo r Cu st o m e rs in Au st ra lia
If the supply cord of AC power adaptor is
damaged the AC power adaptor must be
returned to the manufacturer of his agent for the
cord to be replaced.
Incorrect battery usage may lead to leakage of
battery fluid or bursting batteries. To prevent
such accidents, observe the following
precautions:
Pre ca u t io n s
Rechargeable battery carrying case (1)
Headphones with a remote control (1)
Carrying case (1)
Ear pad (2)
R6 (size AA) battery (World model only) (1)
DISPLAY
3) Appears only with MDs that have been
electronically labeled.
On sa fe t y
3 Connect the power source.
Go forward
keep pressing
Usin g a d ry b a t t e ry
•
Do not put any foreign objects in the DC
IN 1.5 V jack.
while playing1) + or + side of
( on the remote
Elapsed time
•
Install the + and – poles of the batteries
correctly.
The MD is not played normally.
• The player is set to the repeat mode
(“Å“ is displayed).
Tip
The OPERATE lamp lights on the main unit
when the MD Walkman is operating.
Fo r Cu st o m e rs in t h e Un it e d St a t e s
In fo rm a t io n
control
•
•
Do not try to recharge the batteries.
When the player is not to be used for a long
time, be sure to remove the batteries.
If a battery leak should develop, carefully
and thoroughly wipe away battery fluid
from the battery compartment before
inserting new ones.
Op t io n a l a cce sso rie s
AC-E15L AC power adaptor*
DCC-E215 Car battery cord
CPA-9 Car Connecting Pack
MDR-D33, MDR-D55, MDR-D77 Stereo
Headphones
SRS-A41 Sony Active Speakers
CK-MD4 MiniDisc Carrying Case
CK-MD10 MiniDisc Filing Box
On p o w e r so u rce s
LR6 (size AA)
alkaline battery
(not supplied)
b
Press PLAY MODE repeatedly until
“Å“ disappears, then start
playing.
•
For use in your house: Use the AC power
adaptor AC-E15L (not supplied). Do not
use any other AC power adaptor since it
may cause the player to malfunction.
This equipment has been tested and found to
comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC rules.
These limits are designed to provide reasonable
protection against harmful interference in a
residential installation. This equipment
generates, used, and can radiate radio frequency
energy and, if not installed and used in
accordance with the instructions, may cause
harmful interference to radio communications.
However, there is no guarantee that interference
will not occur in a particular installation. If this
equipment does cause harmful interference to
radio or television reception, which can be
determined by turning the equipment off and on,
the user is encouraged to try to correct the
interference by one more of the following
measures:
Notes
•
If t h e p la y d o e s n o t st a rt
Make sure the player is not locked. See "To
lock the controls."
• Do not open the disc compartment shutter
by force, as this may lead to a malfunction.
• Do not slide EJECT during playback. If you
do, the MD will eject and playback will
stop.
An MD is not played from the first track.
• Disc playing stopped before it came to
the last track.
Track name
Track number
To re m o ve t h e MD
No t e o n m e ch a n ica l n o ise
The player gives out mechanical noise while
operating, which is caused by the power-
saving system of the player and it is not a
trouble.
Press p and then slide EJECT2). The disc
compartment shutter opens and the MD
ejects.
b
Press = repeatedly or eject and
reinsert the MD once to go back to
the beginning of the disc, and restart
playing after checking the track
number in the display.
Polarity of the plug
*
The operative voltage for the AC power
adaptor varies depending upon the country in
which it is sold. Therefore, purchase the AC
power adaptor in the country you intend to
use it.
•
•
The player is not disconnected from the AC
power source (mains) as long as it is
connected to the wall outlet, even if the
player itself has been turned off.
If you are not going to use this player for a
long time, be sure to disconnect the power
supply (AC power adaptor, dry batteries,
rechargeable batteries, or car battery cord).
To remove the AC power adaptor from the
wall outlet, grasp the adaptor plug itself;
never pull the cord.
3
Insert an MD.
2 Push in the MD until it
locks in its place. When
the MD is locked in its
place the shutter will
close.
Disc name
Track number
Playback sound skips.
EJECT
Your dealer may not handle some of the above
listed accessories. Please ask the dealer for
detailed information about the accessories in
your country.
• The player is placed where it receives
continuous vibration.
b
Put the player on a stable place.
A very short track may cause sound
to skip.
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment
and the receiver.
• Connect the equipment into an outlet on a
circuit different from that to which the receiver
is connected.
Sound has a lot of static.
• Strong magnetism from a television or
such device is interfering with
operation.
US and foreign patents licensed from Dolby
Laboratories Licensing Corporation.
Number of the track
recorded on the MD.
•
For use in the car: Use the CPA-9 car
connecting pack and the DCC-E215 car
battery cord (not supplied).
Design and specifications are subject to change
without notice.
• Consult the dealer or an experienced radio/ TV
technician for help.
Note
b
Move away from the source of
strong magnetism.
1 Insert an MD on the
Disc and track names appear only with MDs that
have been electronically labeled.
groove of the disc
compartment lid.
The shutter of the
disc compartment
will open when you
insert an MD.
You are cautioned that any changes or
modifications not expressly approved in this
manual could void your authority to operate this
equipment.
Charging the rechargeable battery does
not start. (in case of the charger w ith a
lid)
• The lid of the battery charger is not
closed properly.
b
Close the lid and slide the switch on
it.
|