Sony Speaker SRS D2100 User Manual

3-264-412-11(1)  
Installing the satellite speakers  
(See fig. A)  
Troubleshooting  
Should you encounter a problem with your speaker  
system, check the following list and take the indicated  
measures. If the problem persists, consult your nearest  
Sony dealer.  
C
PC, CD or MD  
Walkman, etc.  
Use the supplied screws to attach the base to the  
satellite speaker. The satellite speaker can be used either  
placed on a desk or attached to a wall.  
There is no sound from the speaker system.  
Act ive Sp e a ke r Syst e m  
Make sure all the connections have been correctly  
made.  
Make sure the VOLUME dial and the each speakers  
volume dial on the control box.  
Make sure the connected component has been turned  
up properly.  
When you use the satellite speaker on a desk  
(See fig. A-A)  
By attaching the base to the satellite speaker, it can be  
placed on a desk.  
Operating Instructions  
Manual de instrucciones  
1
Match the hole of the base and the  
Check if headphones are connected. If they are,  
disconnect them.  
bottom hole of the satellite speaker.  
Attach the base with the anchor holes facing  
forward.  
The sound is distorted.  
Turn down the volume level on the connected  
component. Or, if the connected component has a  
BASS BOOST function, set it to off.  
Rotate BASS on this unit to reduce the bass volume.  
Turn VOLUME on this unit down to reduce the  
volume.  
The base allows you to adjust the satellite speaker  
to the desired angle.  
SRS-D2100  
2
Ensure the screw s are tight.  
Tighten the screw with your finger. If it is difficult,  
use a screwdriver to secure the screw.  
Subwoofer  
2004 Sony Corporation  
Printed in China  
There is hum or noise in the speaker output.  
Front speaker (Left)  
Control box  
Make sure all the connections have been correctly  
made.  
Make sure none of the audio components are  
positioned too close to the TV set.  
When you use the satellite speaker attached  
to a w all (See fig. A-B)  
By attaching the base to the satellite speaker, it can be  
attached to a wall. Follow the Notes (below) to install  
safely. Improper installation may result in the speaker  
falling and causing bodily injury or damage to the  
speaker or other object.  
Owners Record  
The model number and the serial number are located on the rear of the  
subwoofer.  
Record the model number and the serial number in the space provided below.  
Refer to them whenever you call upon your Sony dealer regarding this product.  
Front speaker (Right)  
The sound has suddenly stopped.  
Make sure all the connections have been correctly made.  
The brightness of the POWER indicator is  
unstable.  
The brightness of the POWER indicator may become  
unstable when the volume is turned up. This is not a  
malfunction.  
Model No. SRS-D2100  
Serial No.  
1
Align the hole in the base w ith the hole  
at the rear of the satellite speaker.  
Attach the base with the anchor holes uppermost.  
The base allows you to adjust the satellite speaker  
to the desired angle.  
D
POWER  
PHONES  
Package Contents  
2
3
Ensure the screw s are tight.  
Tighten the screw with your finger. If it is difficult,  
use a screwdriver to secure the screw.  
Specifications  
ON  
OFF  
POWER  
PHONE  
Control box  
MIN  
MAX  
Speaker section  
Satellite speaker  
Speaker system  
Speaker units  
Enclosure type  
Impedance  
VOLUME  
BASS  
Secure the hollow w all anchor in the w all  
— refer to the illustration.  
Full range, magnetically shielded  
5.6 cm, cone type  
Closed type  
6 Ω  
3 m  
VOLUME  
Notes  
Confirm wall thickness is sufficient. A  
minimum thickness of 9.5 mm is recommended  
for plasterboard.  
Cord length  
Subw oofer  
Speaker system  
Speaker units  
Enclosure type  
Impedance  
Subwoofer (1)  
Control box (1)  
Connecting Cable (1)  
Woofer  
VOLUME: Controls total volume level.  
Use the specified clamp (hollow wall anchor,  
not supplied) when attaching to plasterboard.  
Refer to the supplied operating instructions  
using a hollow wall anchor.  
Use wall anchors of at least 20 kg hanging  
capacity.  
16 cm, cone type  
Bass reflex  
6 Ω  
BASS: Adjusts bass level (Subwoofer)  
PHONE: Connect to headphones for personal listening  
Amplifier section  
Rated output  
12 W (10% T.H.D., 1 kHz, 6 )  
(Satellite speaker)  
Refer to the instruction supplied with hollow  
wall anchor.  
80 W (10% T.H.D., 100 Hz, 6 )  
(Subwoofer)  
Satellite speaker (2)  
Base (2)  
Screw (2)  
Requires ø 4 mm hollow wall anchor.  
Set up the head of a hollow wall anchor 5 mm  
from the wall.  
On operation  
Input  
Stereo mini jack × 1 (INPUT 1)  
Stereo mini jack × 1 (INPUT 2)  
4.7 k(at 1 kHz)  
En g lish  
Do not drive the speaker system with a continuous  
wattage exceeding the maximum input power of the  
system.  
Input impedance  
Output  
Stereo mini jack × 1 (PHONES)  
Apply a bond (anaerobic threadlocking  
material) to the hollow wall anchor to prevent  
the screw loosening.  
Before operating the unit, please read this manual  
thoroughly and retain it for future reference.  
A
A
Before connecting, turn off the speaker system, the  
PC and audio component to avoid damaging the  
speaker system.  
The volume level should not be turned up to the  
point of distortion.  
Although this system is magnetically shielded, do not  
leave recorded tapes, watches, personal credit cards  
or floppy disks using magnetic coding in front of the  
system for an extended period of time.  
General  
Dimensions (w/ h/ d) Approx. 130 × 40 × 73 mm  
(5 1  
Approx. 95 × 135 × 150 mm  
(3 3 × 5 3  
× 6 in.) (Satellite speaker,  
on a desk)  
Approx. 95 × 100 × 180 mm  
(3 3  
in.) (Satellite speaker,  
/
8
× 1 5  
/
8
× 2 7  
/
8
in.) (Control box)  
Base  
4
Attach the satellite speaker to the w all.  
Insert both wall anchors in the anchor holes of the  
satellite speaker base.  
WARNING  
/
4
/
8
To prevent fire or shock hazard, do not expose the  
unit to rain or moisture.  
To avoid electrical shock, do not open the cabinet. Refer  
servicing to qualified personnel only.  
To prevent fire, do not cover the ventilation of the  
apparatus with news papers, table-cloths, curtains, etc.  
Do not place lighted candles on the apparatus.  
To prevent fire or shock hazard, do not place objects  
filled with liquids, such as vases, on the apparatus.  
Screw  
Note  
,
/
4
× 4 × 7 1  
/
8
Ensure that the satellite speaker is securely  
attached to the wall before use.  
attached to a wall)  
Satellite speaker  
Approx. 285 × 285 × 462 mm  
(11 1  
/
4
× 11 1  
/
4
× 18 1  
/
4
in.)  
The speaker angle can  
be changed by  
If the TV picture or monitor display is  
magnetically distorted  
(Subwoofer)  
Mass  
Approx. 200 g (7 oz.) (Control box)  
Approx. 490 g (1 lb. 1 oz.)  
(Satellite speaker)  
attaching the base  
back to front.  
Hooking up the system  
(See fig. B)  
Attach the base with the  
anchor holes facing forward  
Although this system is magnetically shielded, there may  
be cases that the picture on some TV sets/ personal  
computers may become magnetically distorted. In such a  
case, turn off the power of the TV set/ personal computer  
once, and after 15 to 30 minutes turn it on again. In the  
case of a personal computer, take appropriate measures,  
such as data storage, before turning it off.  
When there seems to be no improvement, locate the  
system farther away from the TV set/ personal  
computer. Furthermore, be sure not to place objects in  
which magnets are attached or used near the TV set/  
personal computer, such as audio racks, TV stands, toys  
etc. These may cause magnetic distortion to the picture  
due to their interaction with the system.  
Approx. 8.2 kg (18 lb. 1 oz.)  
(Subwoofer)  
Do not install the appliance in a confined space,  
such as a bookcase or built-in cabinet.  
Attach the base with the  
anchor holes uppermost  
Cord length  
2 m (Control box to subwoofer)  
2 m (Power cord)  
1
2
Connect the cord of the control box to  
the 8-pin Din jack of the subw oofer w ith  
their respective arrow s aligned.  
B
Anchor holes  
CAUTION  
Power consumptions  
31 W  
Hollow wall anchors  
(ø 4 mm, not supplied)  
You are cautioned that any changes or modification not  
expressly approved in this manual could void your  
authority to operate this equipment.  
Supplied accessories  
Connecting Cable  
Connect the satellite speakers to the  
subw oofer.  
Confirm the location of the satellite speakers, and  
then connect to their respective jacks.  
NOTICE FOR THE CUSTOMERS IN THE USA  
Optional accessories  
Connecting cord RK-G136, RK-G138  
Plug adaptor PC-236MS  
,
Satellite speaker  
Design and specifications are subject to change without  
notice.  
3
Connect the control box to the source  
equipment.  
On placement  
Screw  
Base  
40 mm  
Do not set the speakers in an inclined position.  
Do not leave the system in a location near heat  
sources, or in a place subject to direct sunlight,  
excessive dust, moisture, rain or mechanical shock.  
Do not install the satellite speaker anywhere other  
than on a wall.  
– PC, etc.:  
Connect the INPUT1 jacks of the control box and  
the LINE OUT or headphones jack of a PC, etc.  
with the supplied connecting cord. For details,  
refer to the operating instructions of the PC.  
Note  
First, be sure to apply a bond (anaerobic  
threadlocking material) to the hollow wall  
anchor to prevent the screw loosening.  
This symbol is intended to alert the user to  
the presence of uninsulated “dangerous  
voltage” within the products enclosure  
that may be of sufficient magnitude to  
constitute a risk of electric shock to persons.  
– CD/MD Walkman, etc.:  
Do not hang on the satellite speaker or hang anything  
on it.  
Connect the INPUT2 jack of the control box and  
the LINE OUT or headphones jack of a CD/ MD  
Walkman, etc. The connecting cord is not supplied  
with this system.  
5 mm  
On cleaning  
Do not use alcohol, benzene, or thinner to clean the  
cabinet.  
7 mm  
Note  
This symbol is intended to alert the user to  
the presence of important operating and  
maintenance (servicing) instructions in the  
literature accompanying the appliance.  
To switch INPUT1 and INPUT2, use ON/ OFF of  
the device connected to the control box.  
ø 4 mm  
If you have any questions or problems concerning your  
speaker system, please consult your nearest Sony  
dealer.  
4
5
Connect the subw oofer to the w all  
outlet.  
Note  
Do not hang on the satellite speaker or hang  
anything on it.  
9.5 mm or more  
Precautions  
Position the speakers. (See fig. C)  
On safety  
The nameplate indicating operating voltage, power  
consumption, etc., is located on the rear exterior.  
B
Before operating the system, be sure that the  
operating voltage of the system is identical with that  
of your local power supply.  
Listening to the sound (See fig. D)  
First, turn down the volume on the control box. The  
volume should be set to minimum before you begin  
playing the programme source.  
Connecting cord  
(not supplied)  
to LINE OUT or  
headphones jack  
CD/MD  
Walkman*, etc  
(stereo mini-jack)  
to INPUT2 jack  
Where purchased  
U.S.A./ Canada  
Operating voltage  
120 V AC, 60 Hz  
1
Set the POWER sw itch to ON on the  
control box.  
The POWER indicator lights up.  
European countries 220 – 230 V AC, 50 Hz  
Control Box  
(rear)  
Other countries  
• 110 – 120 V AC, 50/ 60 Hz  
• 220 – 230 V AC, 50 Hz  
to INPUT1 jack  
to 8-pin Din jack  
The unit is not disconnected from the AC power  
source (mains) as long as it is connected to the wall  
outlet, even if the unit itself has been turned off.  
Unplug the system from the wall outlet if it is not to  
be used for an extended period of time. To disconnect  
the cord, pull the cord by grasping the plug. Never  
pull the cord itself.  
Should any liquid or solid object fall into the system,  
unplug the systems power cord and have the system  
checked by qualified personnel before operating it  
any further.  
The AC power cord should be changed only at a  
qualified service shop.  
For efficient heat dissipation, ensure there is sufficient  
space to the rear of the subwoofer. Also, avoid  
placing objects on the unit.  
2
Adjust the VOLUME control on the  
control box.  
You can adjust the volume of the subwoofer and  
each satellite speaker.  
When connecting to the headphone output, also  
adjust the volume of the connected component.  
After listening, set the POWER switch to OFF.  
The POWER indicator goes off.  
Connecting  
Cable  
(supplied)  
to LINE OUT or  
headphones jack  
Satellite speaker  
(rear)  
PC, etc.  
3
Using headphones/earphones.  
Connect headphones/ earphones to the PHONES  
jack on the control box.  
Note  
Turn off the MEGA BASS or BASS BOOST  
(Walkman, etc.) function as it may cause audible  
distortion.  
to Front R jack  
to Front L jack  
Subwoofer (rear)  
Do not insert your hand or any objects into the hole of  
the subwoofer.  
*
“WALKMAN” is a registered  
trademark of Sony Corporation to  
represent Headphone Stereo products.  
to wall outlet  
 

Sharp Stereo System XL UH240 User Manual
Sony Camera Lens 30M28 User Manual
Sony Camera Lens SAL 85F28 User Manual
Sony Car Stereo System CDX 5100 User Manual
Sony Cell Phone 1264 0772 User Manual
Sony Video Game Console SCPH 50011 User Manual
Southbend Fryer BELM 30 User Manual
Southbend Lathe SB1049F User Manual
Sunbeam Blender PB7650 User Manual
SUPER MICRO Computer Computer Hardware MBDX7DA3O User Manual