Stiga Tiller 82R2 H User Manual

ST IG A  
Silex 82R2-H  
BRUKSANVISNING SV ....5  
KÄYTTÖ O HJEET FI ...12  
BRUGSANVISNING DA..19  
BRUKSANVISNING NO .26  
GEBRAUCHSANW EISUNG DE...33  
INSTRUCTIO NS FO R USE EN...41  
MO DE DEMPLO I FR....48  
GEBRUIKSAANW IJZING NL...55  
ISTRUZIO NI PER L’USO IT.....62  
INSTRUCCIO NES DE USO ES....69  
INSTRUÇõES DE UTILIZAÇÃO PT ...77  
INSTRUKCJA O BS£UGI PL....85  
»HC“P”K÷»fl œOÀ‹«Œ¬¿“EÀfl RU...92  
NÁVO D K PO U®ITÍ CZ 100  
HASZNÁLATI UTASÍTÁS HU107  
NAVO DILA ZA UPO RABO SL..114  
8214-2213-80  
 
5
4
A
E
B
C
V
D
7
6
K
I
H
I
F
J
K
9
8
L
R
3
 
11  
10  
1
2
4
3
13  
12  
L
K
U
J
15  
14  
M8 x 40  
M8 x 45  
M
O
N
4
 
GB  
ENGLISH  
Set the throttle control in the "Stop" position,  
and close the petrol cock when the machine has  
been stopped.  
Switch off the engine before transporting the  
machine. Never lift the machine by yourself.  
The machine is lifted by two persons, one on  
each side holding the steering and the rotor ax-  
le. Wear protective gloves and hold the machine  
upright when lifting.  
1 SYMBOLS  
The following symbols can be found on the rotary  
cultivator/in these instructions. These will provide  
a reminder of the care and attention that is required  
during operation. If any symbol is missing, has  
been damaged or is illegible, it must immediately  
be replaced with a new one.  
This is what the symbols mean:  
Warning! Read the owner’s manual before  
operating the machine.  
When the machine is loaded on a trailer or tail-  
board it should be run up on a ramp by using its  
wheel.  
Warning! Rotating blade.  
2.2 PREPARATIONS  
Before starting work, remove all foreign objects  
such as stones, glass, cables, metal objects and  
other loose objects.  
Toys, hoses and other objects can be damaged.  
Check that the tiller is in good condition before  
using it.  
Warning! This symbol highlights impor-  
tant text in these instructions. Risk of seri-  
ous personal injury or damage to the  
machine if the instructions are not fol-  
lowed.  
Check that all nuts and bolts are tightened.  
2 SAFETY INSTRUCTIONS  
2.1 GENERAL  
2.3 OPERATING  
Read through this instruction book carefully  
and make sure you understand the contents be-  
fore using the tiller.  
Always operate the machine at low speed when  
working on stony ground.  
Do not change the engine's speed setting. The  
engine must not be overspeeded.  
The work area should be well illuminated dur-  
ing the work.  
The tiller must not be used when other persons,  
especially children, are in the vicinity.  
The tiller must not be used without the splash-  
guards or protective cover.  
The tiller must not be used if the operator is ill,  
has taken medicine, or is under the influence of  
other substances which reduce one's reactions.  
The tiller must not be used on terrain which  
slopes more than 20°.  
The user is responsible to ensure that all risks in  
the terrain are taken into consideration, and that  
procedures are taken to prevent accidents. This  
particularly applies to sloping, slippery or loose  
terrain.  
Start the engine carefully, according to the in-  
structions in this manual. No parts of the body  
must come in contact with the rotors.  
The engine must never be started in an enclosed  
area.  
The tiller must only be used for gardening pur-  
poses.  
Keep children away from the tiller.  
Do not allow children or persons who have not  
read the instructions to handle the tiller.  
The tiller is manufactured in accordance with  
current standards, and must not be modified or  
rebuilt.  
All the symbols on the tiller should be kept in-  
tact.  
The user is liable for damages incurred by a  
third party.  
WARNING for petrol. Petrol is highly inflam-  
mable: Petrol must be stored in the requisite  
containers.  
Always fill-up outdoors and with the engine  
switched off.  
Do not smoke when filling-up.  
There must be no naked flames or other sources  
of heat in the vicinity of the petrol.  
Do not start the engine if petrol has spilled out.  
Move the machine and allow the petrol to evap-  
orate before starting the machine.  
The carbon monoxide in the engine's exhaust  
fumes is poisonous and can cause death.  
Screw on the filler cap correctly after filling up.  
41  
 
GB  
ENGLISH  
Wear tightly fitting clothes and heavy-duty  
shoes which completely cover the feet.  
The tank should only be half full when operat-  
ing on slopes. Petrol can leak out.  
The engine must be stopped in the following  
circumstances:  
When the machine is left unattended  
Before the machine is filled up with petrol  
Always make sure you have a good footing, es-  
pecially on slopes.  
Check that no one is in front of you or beside  
you when starting the blades. Keep a steady  
grip on the steering. The machine will lift when  
the rotors are started. Use extra caution when  
backing.  
Always keep at a safe distance to the rotors  
when working.  
jury. If the muffler is damaged it must be re-  
placed.  
The engine must be stopped and the spark plug  
lead disconnected in the following circumstanc-  
es:  
When adjusting the rotors.  
When the machine is to be cleaned or repaired.  
When checking after a collision with a solid  
hard object. Carry out the necessary repairs be-  
fore continuing to work.  
If the machine begins to vibrate abnormally.  
Carry out the necessary repairs before continu-  
ing to work.  
Wear protective gloves when working with the  
rotors.  
Holding the steering correctly ensures a safe  
distance.  
No person must come closer than 20 m to the  
machine when working on slopes. The user  
must hold the steering firmly with both hands  
all the time.  
3 ASSEMBLY  
3.1 Depth skid  
1. Install the depth skid mounting arm (4:B) in the  
machine and lock using the pin (4:A) and lock-  
ing pin (4:D).  
Working on stony or hard ground demands ex-  
tra attention from the operator. The machine be-  
comes more unstable.  
Never touch the engine when operating the ma-  
chine, or just afterwards. Risk for burn injuries.  
2. Install the depth skid (4:V) in the mounting arm  
(4:B) and lock at the desired height using lock-  
ing screw (4:C). Also see “4.18”.  
3.2 Handle’s support  
Install the handle’s support (5:E) on the machine.  
Use the 4 screws, nuts and washers as illustrated in  
fig. 5.  
2.4 AFTER OPERATING  
Allow the engine to cool before putting the ma-  
chine in a storeroom. Fire risk!  
Remove dirt and foreign material before putting  
the machine in a storeroom. The area round the  
petrol tank and muffler must be kept clean from  
leaves, oil, petrol or other foreign materials.  
Fire risk!  
If the petrol tank is to be emptied, do this out-  
doors and when the engine is cold. Fire risk!  
The machine should be stored in a dry place.  
The machine must not stored with fuel in the  
tank in rooms where there are naked flames,  
sparks or other strong sources of heat.  
3.3 Handle  
1. Slide up the reinforcement plate (6:F) from un-  
derneath in the handle’s stay so that the holes  
correspond.  
2. Install the handle with the through screw (7:H)  
with two washers and nuts as well as the knob  
(7:1) with 4 washers and screw (7:J). The wave  
shaped washers (7:K) must be turned with the  
wave shape facing inwards. Check that the  
screws also go through the reinforcement plate  
(6:F).  
3. Install the handle’s cross member (8:L) with the  
supplied screws and nuts.  
4. Install the cover (1:I) with 4 screws from under-  
neath.  
2.5 MAINTENANCE  
Carry out maintenance regularly. All nuts and  
bolts should always be tight.  
Only use genuine spare parts which are in good  
condition. Spare parts must not be repaired.  
They must be replaced if they are defective.  
Poor quality spare parts can lead to personal in-  
3.4 Cover  
Install the cover (1:I) with the supplied screws  
from underneath.  
42  
 
GB  
ENGLISH  
3.5 Throttle cable  
4.1 Reverse control (1:A)  
1. Install the throttle cable on the engine if not al-  
ready installed. See the engine supplier’s man-  
ual.  
The control is used to start the rotor for reverse  
when the engine is running.  
Control in idle mode (released): No drive.  
Control depressed: The machine reverses.  
2. Pull up the cable under the support’s (5:E) up-  
per section and over the screws in fig. 7.  
4.2 Drive control (1:B)  
3. Install the cable in the throttle. See fig. 11.  
The control consists of a loop, positioned between  
the left and right handle.  
The control is used to start the rotor for forward  
motion when the engine is running.  
Control in idle mode (downward): No drive.  
Control pressed up: Forward drive.  
3.6 Cables  
Pull up the cables under the cover under the sup-  
port’s (5:E) upper section and over the screws in  
fig. 7. Then install the ends into the relevant con-  
trol as follows:  
1. Install the cable ends into the relevant control.  
The cable marked (R) must be installed into the  
reverse control. See fig. 9.  
2. Install the cable’s adjuster sleeves into the slots  
in the handle. See fig. 10.  
4.3 Stop (1:C)  
The stop control is located in the middle of the  
throttle and has two positions as follows:  
ON: The engine can be started and operated.  
OFF: The engine stops and cannot be started.  
3. Slide the electric cable on the stop control’s flat  
pin. See fig. 11.  
4.4 Throttle (1:D)  
3.7 Gear lever  
The throttle controls the engine’s revs.  
Idle: Control in the rear position.  
Install the gear lever (1:U) as follows:  
1. Insert the gear lever (12:U) through the oval  
hole in the machine.  
Full throttle and start: Control in the front position.  
2. Install the washer (13:J) on the gear lever screw.  
3. Press the gear lever’s ball into the lever socket.  
4. Install the lock the (13:K) so that the gear lever  
locks into the lever.  
4.5 Handle (1:E)  
The handle has two handgrips that are used to op-  
erate the machine over the area to be cultivated.  
The handle can be adjusted as follows:  
5. Install the washer and nut (13:L) and tighten.  
Laterally (angle) by releasing the lever (1:J).  
Vertically by releasing the knobs (1:S).  
3.8 Rotor  
Install the outer rotors (14:N) and cutting discs  
(14:O).  
4.6 Fuel cap (1:F)  
Unscrew the fuel cap to fill with petrol. The fuel  
cap must always be closed during operation.  
Note that the holes in shafts and sleeves must cor-  
respond before the screws are installed.  
Install the screws with the stated lengths according  
to fig. 14.  
4.7 Protective grille (1:H)  
The protective grille must always be installed dur-  
ing operation. There are surfaces that become ex-  
tremely hot under the protective grille that risk  
causing personal injury if touched.  
3.9 Splash guards  
Install the outer splash guards (15:M) with screws,  
nuts and washers according to fig. 15.  
4.8 Cover (1:I)  
The cover protects cables and the handle adjust-  
ment.  
4 DESCRIPTION  
4.9 Oil filling (K)  
The rotary cultivator is driven by a four-stroke en-  
gine and is intended for soil cultivation in private  
gardens. The most important parts and controls of  
the rotary cultivator are described below.  
Always check the oil level before start-  
ing the engine.  
Plug for oil filler and checking the oil level.  
43  
 
GB  
ENGLISH  
4.10Oil draining (1:L)  
The screw is removed when used engine oil is to be  
drained.  
4.15Fuel cock (1:Q)  
The fuel cock should be open during operation and  
closed when the machine is not used.  
The fuel cock has the following positions:  
Forwards:Open  
Back: Closed  
4.11Auxiliary wheel (1:M)  
The auxiliary wheel is intended to assist transport  
of the machine and has two positions.  
The auxiliary wheel must be folded up  
when carrying out work.  
4.16Starter handle (1:R)  
Handle for starting the engine.  
4.17Gear control (1:U)  
Select between two gears and neutral with the gear  
control as follows:  
The auxiliary wheel must be down when  
transporting.  
Position 1:The rotor rotates slower and with more  
power. Use this position when the ground  
is hard.  
Position 2:The rotor rotates at normal speed.  
Position N:No drive.  
The auxiliary wheel is folded up and down as fol-  
lows:  
1. Pull out the auxiliary wheel stay to the left in the  
driving direction of the machine. See fig. 2.  
2. Raise the auxiliary wheel so that its locking  
mechanism is under the member in the ma-  
chine.  
3. Release the auxiliary wheel stay so that the  
locking mechanism locks under the member in  
the machine.  
4.18Depth skid (1:S)  
The task of the depth skid is to keep the machine  
stable so that the soil can be cultivated.  
The depth skid can be set and locked laterally us-  
ing a screw (3:W) on each side.  
The different operating properties are shown ac-  
cording to the table below:  
4. Lower in reverse order.  
4.12Rotors (1:N)  
Direction  
Properties  
Nobody must be close to the dangerous  
rotors during operation.  
Left  
The machine works itself for-  
ward , angled to the left.  
The rotors are made of special steel and work the  
soil at the same time as the machine is propelled  
forwards.  
Middle  
Right  
The machine works itself for-  
ward without being angled to  
either side.  
The machine works itself for-  
ward, angled to the right.  
4.13Cutting disc (1:O).  
Nobody must be close to the dangerous  
cutting discs during operation.  
Set the depth skid vertically and turn by slackening  
off the screw (3:X), set the depth skid in the de-  
sired position and then tighten the screw.  
Remove the depth skid with mounting arm by pull-  
ing the pin (1:T) upwards. The pin is locked by a  
locking pin underneath.  
The cutting discs are on respective rotor  
axles and are designed to border the working area  
and facilitate control of the machine.  
4.14Choke (1:P)  
The choke must never be activated dur-  
ing operation. This will damage the en-  
gine.  
5 OPERATION  
5.1 Fuel  
The choke must be activated at cold starts.  
The fuel cock has the following positions:  
Forwards: Open. Used for hot starts and operating  
.
Read and understand all safety instruc-  
tions.  
No fires or smoking near to petrol.  
Back: Closed. Always for cold starts.  
Use 92-95 octane lead free petrol.  
44  
 
GB  
ENGLISH  
Oil-mixed petrol designed for 2-stroke engines  
must never be used.  
Filling  
4. Hold the handle with one hand and slowly pull  
the starter handle with the other hand. See  
“4.16”. When the starter mechanism engages,  
quickly and forcefully pull the starter handle  
until the engine starts.  
NOTE! Do not pull the cord hard to its stop po-  
sition and do not release it in the pulled out po-  
sition. This damages the starter mechanism.  
Read and understand all safety instruc-  
tions.  
If the engine has been running, wait a  
few minutes until it has cooled before  
filling up.  
5. Reset the choke after 3-5 seconds.  
Fill carefully to prevent the spillage of  
fuel.  
5.2.2 Starting a warm engine  
Start a hot engine according to points 1, 3 and 4  
above. The choke must not be used.  
Move the rotary cultivator at least 3 me-  
tres from the filling site before starting.  
Fill as follows:  
1. Clean around the fuel cap.  
2. Unscrew the filler cap.  
5.3 Operating  
1. Tip the rotary cultivator back slightly so that the  
rotor is above ground.  
2. Activate the drive control (1:B).  
3. Tilt the cultivator forward so that it works its  
way into the soil.  
3. Fill using a funnel or use a filler can with spout  
to prevent spillage.  
4. Tighten the filler cap.  
4. To reverse, activate reverse control (1:A).  
5. Move the rotary cultivator at least 3 metres  
from the place of filling before starting.  
5.4 Stop  
Move the rotary cultivator at least 3 me-  
tres from the filling site before starting.  
1. Stop the rotary cultivator by setting the throttle  
and stop control (1:C) to “OFF”.  
2. Shut off the fuel cock. See “4.15”.  
5.2 Engine Oil  
5.5 Operating tips  
Always check the oil level before start-  
ing. Otherwise there is a risk of serious  
engine damage.  
The rotors propel the machine forward. The speed  
of the rotors is controlled by the throttle (1:D).  
Keep hands and feet away from rotating  
parts (1:N).  
Also see “4.9” and “4.10”. Check the oil level as  
follows:  
1. Position the machine so that the engine is hori-  
zontal.  
2. Unscrew the oil filler and check that the oil lev-  
el is level with the lower part of the hole’s  
thread.  
3. Top up the oil if necessary. Use normal engine  
oil SAE 10W-30.  
4. Reassemble the oil filler cap.  
The optimum working depth varies with soil con-  
ditions. The working depth is determined by how  
hard the depth skid is pushed down during propul-  
sion. Operate and test.  
Drive 2-3 times in different directions for best re-  
sults.  
Never operate the machine in wet soil. Clumps of  
earth are created that are then difficult to break-up.  
Hard and dry soil requires an extra run, at right an-  
gles to the first.  
Move the rotary cultivator at least 3 me-  
tres from the filling site before starting.  
WARNING! Never overload a new ma-  
chine. Drive carefully for the first 5  
hours.  
5.2.1 Starting the engine from cold  
1. Open the fuel cock. See “4.15”.  
2. Put the choke in position “CHOKE”. See  
“4.14”.  
3. Set the throttle (1:D) in the “START” position.  
6 STORAGE  
Store the rotary cultivator in a dry place. Also see  
section “Safety instructions”.  
After draining the petrol, start the engine and allow  
it to run until it runs out of petrol.  
45  
 
GB  
ENGLISH  
7.3 Spark plug (1:Y)  
7 MAINTENANCE  
WARNING!Repairs must be carriedout  
by the dealer. Otherwise the guarantee  
becomes invalid.  
WARNING!Before carrying out repairs  
and maintenance, the spark plug con-  
nection must be disconnected.  
The sparkplug must be replaced in the following  
cases.  
When the electrodes are burnt.  
If the porcelain insulator indicates damage.  
If the rotary cultivator is difficult to start.  
The electrode gap should be 0.7-0.8 mm.  
Use sparkplug Champion QC12YC or similar.  
7.1 Periodic maintenance  
7.4 Changing the oil  
Before each operation  
Change the oil the first time after 2 hours of oper-  
ation, and subsequently every 25 hours of opera-  
tion or at least once a season. Change oil when the  
engine is warm.  
Check for fuel leaks.  
Check that all screws are tightened.  
After each operation  
The engine oil may be very hot if it is  
drained off directly after the engine is  
shut off. So allow the engine to cool a few  
minutes before draining the oil.  
Clean the rotary cultivator.  
Check for fuel leaks.  
Every 25 operating hours and every 3 months  
Check, clean or replace the air filter.  
1. Lean the machine slightly so that the oil drain-  
ing plug is the lowest point of the engine.  
Check that all screws and nuts are tightened.  
2. Unscrew the oil draining plug. See “4.10”.  
3. Let the oil run out into a container.  
4. Screw back the oil draining plug.  
5. Fill with new oil: See “5.2”.  
7.2 Air filter (1:G)  
Do not use flammable liquids when  
cleaning.  
Serious engine damage can be caused if  
the machine is operated with a defective  
or blocked filter.  
The paper filter must never be cleaning  
with liquid.  
7.5 Cleaning  
Never use high-pressure washing equip-  
ment when cleaning. This can cause wa-  
ter to penetrate between the seals and  
cause machine damage.  
The machine is equipped with a pre-filter (foam  
rubber) and a main filter (paper).  
Clean/replace the air filter every 3 months or every  
25 operating hours. During operation in dry and  
dusty conditions, the air filter must be cleaned/re-  
placed every day.  
Clean/replace the air filter as follows:  
1. Undo the screws or locking tabs and the filter  
housing.  
First brush off all dirt. Then wipe down the rotary  
cultivator using a damp cloth. The underside can  
be washed with water.  
7.6 Fault-tracing  
Fault: Difficult to start  
Cause: The fuel is too old.  
Action: Drain the tank and fill with fresh petrol.  
Cause: Sparkplug fault.  
Action: Replace spark plug.  
Fault: Engine runs unevenly  
Cause: Contaminated fuel.  
Action: Clean the petrol tank and carburettor.  
Cause: Sparkplug fault.  
Action: Replace spark plug.  
Fault: Weak engine, does not run at full throttle  
Cause: Blocked air filter  
Corrective action: Clean or replace the air filter.  
Fault: Stops during operation  
Cause: No fuel.  
2. Grasp the main filter (paper) and shake it a few  
times against a hard surface or blow clean with  
compressed air from the inside out.  
3. Wash the pre-filter (foam rubber) in liquid de-  
tergent and water. Then carefully twist the filter  
out and allow to dry.  
4. When the pre-filter is dry, reinstall the filter in  
reverse order.  
The filters must be replaced if very dirty or defec-  
tive.  
Action: Fill with petrol  
46  
 
GB  
ENGLISH  
8 SERVICE  
Authorised service stations carry out repairs and  
servicing. They always use genuine spare parts.  
Under no circumstances may parts oth-  
er than genuine spare parts be used.  
This is a requirement stipulated by the  
Testing Authority. The machine is ap-  
proved and tested with these parts.  
If the machine requires servicing, repair  
or maintenance that entails dismantling  
of the cover, this must be performed by  
an authorised service station.  
The manufacturer reserves the right to make alter-  
ations to the product without prior notification.  
9 PURCHASE TERMS  
A full warranty is issued against manufacturing  
and material defects. The user must carefully fol-  
low the instructions given in the enclosed docu-  
mentation.  
Warranty period  
According to relevant laws.  
Exceptions  
The warranty does not cover damage due to:  
-
Neglect by users to acquaint themselves with  
accompanying documentation  
-
-
-
-
Carelessness  
Incorrect and non-permitted use or assembly  
The use of non-genuine spare parts  
The use of accessories not supplied or approved  
Neither does the warranty cover:  
-
-
Wear parts  
Normal wear  
The purchaser is covered the national laws of each  
country. The rights to which the purchaser is enti-  
tled with the support of these laws are not restrict-  
ed by this warranty.  
GGP reserves the right to make alterations to the  
product without prior notification.  
47  
 

Sonance Speaker 423M User Manual
Sony Camera Lens VADPHB User Manual
Sony Cell Phone 1261 4434 User Manual
Sony Home Theater System DAV DX255 User Manual
Sony Laptop 104 User Manual
Sony Microcassette Recorder ICDUX523 G User Manual
Sony MP3 Player D EG3 User Manual
Sony PDAs Smartphones VCL 04HS User Manual
Sony Portable CD Player D EJ815 User Manual
Tamron Camera Lens AFB016C700 User Manual