Sunbeam Outdoor Ceiling Fan FA7200 User Manual

Sunbeam Remote Controlled  
Tower Fan  
Instruction Booklet  
FA7200 90cm Remote Controlled Tower Fan  
Please read these instructions carefully  
and retain for future reference.  
 
Sunbeam’s Safety Precautions  
Sunbeam are very safety conscious when  
designing and manufacturing consumer prod-  
ucts, but it is essential that the product user  
also exercise care when using an electrical  
appliance. Listed below are precautions which  
are essential for the safe use of an electrical  
appliance:  
Do not use an appliance for any purpose other  
than its intended use.  
Do not place an appliance on or near a hot gas  
ame, electric element or on a heated oven. Do  
not place on top of any other appliance.  
Do not let the power cord of an appliance hang  
over the edge of a table or bench top or touch  
any hot surface.  
For safety reasons and to avoid maintenance  
by unskilled persons, some appliances are  
‘sealed’ using tamperproof screws. Such  
appliances should always be returned to the  
nearest Sunbeam Appointed Service Centre for  
adjustment or repair if required.  
Read carefully and save all the instructions  
provided with an appliance.  
Always turn the power off at the power outlet  
before you insert or remove a plug. Remove by  
grasping the plug - do not pull on the cord.  
Turn the power off and remove the plug when  
the appliance is not in use and before cleaning.  
Do not operate any electrical appliance with a  
damaged cord or after the appliance has been  
dropped or damaged in any manner. If damage  
is suspected, return the appliance to the  
nearest Sunbeam Appointed Service Centre for  
examination, repair or adjustment.  
For additional protection, Sunbeam recommend  
the use of a residual current device (RCD)  
with a tripping current not exceeding 30mA in  
the electrical circuit supplying power to your  
appliances.  
Do not use your appliance with an extension  
cord unless this cord has been checked and  
tested by a qualied technician or service  
person.  
Always use your appliance from a power  
outlet of the voltage (A.C. only) marked on the  
appliance.  
Close supervision is necessary when your  
appliance is being used near children or inrm  
persons.  
Never leave an appliance unattended while in  
use.  
Do not immerse the appliance in water or any  
other liquid.  
Young children should be supervised to ensure  
that they do not play with the appliance.  
If you have any concerns regarding the performance and use of your appliance,  
Ensure the above safety precautions are understood.  
1
 
Safety Precautions For  
Your Tower Fan  
Do not use outdoors.  
The fan must not be used if the guards are  
damaged in any way.  
Do not insert or allow foreign objects to enter  
any ventilation or exhaust openings as this may  
cause electric shock or re, or damage to the  
fan.  
Do not run the cord of the fan under carpeting.  
Do not cover the cord with throw rugs, runners  
or other oor coverings. Arrange the cord away  
from trafc areas so that it will not be tripped  
over.  
Do not use this fan in the immediate surrounds  
of a bath, shower, laundry area or swimming  
pool.  
Be sure the fan is placed on a dry, even  
surface. Do not use on soft surfaces, such as  
beds, where opening may become blocked.  
Keep your fan away from heat sources,  
corrosive gases and avoid direct sunlight.  
This fan is only to be used with the base tted  
and in good condition.  
Disconnect the power plug before dismantling,  
assembling or before cleaning.  
Always unplug the fan when not in use for any  
long length of time.  
Never insert ngers, pencils or any other  
objects through the guards whenever the power  
plug is connected, especially while running.  
Avoid touching mobile parts of the fan.  
Do not attempt to move your fan whilst it is  
operating. If your fan needs to be moved,  
please ensure that it is turned off and you use  
the carry handle on top of the tower.  
When scrapping the fan at the end of its useful  
life, follow local regulations.  
Important Instructions - Retain For  
Future Use  
If you have any concerns regarding the performance and use of your appliance,  
Ensure the above safety precautions are understood.  
2
 
Locating Your Tower Fan  
1.Always locate your fan on a at level surface.  
2.Your tower fan should be located in a dry,  
cool, well ventilated location. Keep your fan  
away from heat sources, corrosive gases and  
avoid direct sunlight.  
3.Do not attempt to move your tower fan  
whilst it is operating. If your fan needs to be  
moved, please ensure that it is turned off  
and you use the carry handle at the rear of  
the fan.  
3
 
Features Of Your Sunbeam  
Tower Fan  
Remote control storage  
When not in use, store your remote control in the handy  
storage compartment on the rear of the fan body.  
Carry handle  
Convenient carry handle allows you to easily carry your fan  
from room to room.  
Power button  
Simply press the power button to turn the unit on.  
Control panel  
The easy to read control panel allows you to quickly  
see what functions have been selected on your tower  
fan.  
4
 
Remote control  
Adjust the fan setting, auto off or oscillation  
from anywhere in the room using the full  
function remote control.  
Auto Off button  
Fan speed button  
The auto off timer allows  
you to set your tower fan to  
turn off after either 1, 2, 4  
or 8 hours.  
Choose from 3 speed  
settings, low medium  
or high.  
Nature and Sleep mode  
Oscillation  
When used in nature mode, the fan speed  
is randomly adjusted, giving the feeling of  
a natural breeze.  
Your tower fan oscillates 70°,  
distributing cool air throughout  
the room.  
Sleep mode is designed to be used when  
retiring to bed; the fan speed is gradually  
decreased until the unit is operating on  
low speed, and when used in conjunction  
with the auto off timer, will ultimately  
switch the unit off.  
5
 
Assembling Your Tower Fan  
Remove the screws from beneath the tower  
Join the two halves of the base together  
1.Using a phillips head screwdriver, remove the  
4 screws from underneath the tower.  
1.Feed the cord between the two halves of the  
base.  
2.Put the screws aside. You will need them to  
secure the base.  
2.Clip the two halves of the base together,  
ensuring the cord remains within the channel  
formed when the two halves come together.  
6
 
Assembling Your Tower Fan (continued)  
Lower the tower onto the base  
Screw the tower to the base  
1.Align the tower and the base as shown.  
2.Push the tower down onto the base until it is  
1.Use the 4 screws you put aside earlier to  
secure the tower to the base.  
rmly held into position.  
2.Clip the power cord into the semi circular  
slot at the edge of the base. Ensure that the  
cord ts neatly into the channel.  
3.Stand the fan upright. It is now ready for  
use.  
7
 
Using Your Tower Fan  
Switching the fan on  
Selecting a fan speed setting  
1.Place the fan on a at level surface.  
2.Insert the plug into a 230/240V power outlet  
and turn the power on.  
Your Sunbeam tower fan has 3 speed settings  
as follows:  
low speed  
medium speed “2” light illuminates  
high speed “3” light illuminates  
“1” light illuminates  
3.Press the power button  
.
4.Press the fan speed button  
to select  
To select a fan speed, simply press the fan  
speed button on the tower or the remote.  
low, medium or high depending on your  
preference.  
Each press of the button will increase the  
fan speed and then return back to the lowest  
speed again.  
Switching the fan off  
To switch the fan off, simply press the power  
button  
.
While the fan remains plugged in to the  
power socket, the fan will remember your last  
fan speed, oscillation and mode setting for  
the next time you switch the fan on again.  
If you will not be using the fan for a length of  
time, it is advisable to turn the power off at  
the wall socket and unplug the power cord.  
8
 
Using Your Tower Fan (continued)  
Using the remote control  
Changing the batteries  
1.Remove the remote control from its compart-  
ment at the rear of the tower as shown.  
1.Slide the rear cover off the remote control  
unit.  
2.Point the remote towards the control panel  
on the front of the tower to operate.  
2.Replace the spent batteries with 2 fresh AAA  
batteries as shown.  
3.Replace the rear cover.  
9
 
Using Your Tower Fan (continued)  
Using the oscillation function  
Using the auto off timer  
The 70 degree oscillation function can be  
used on any setting.  
The auto off timer automatically switches the  
fan off after a preset number of hours.  
1.Turn the unit on and select any fan speed.  
To activate this feature, simply press the auto  
2.Press the  
button on the tower or the  
off button  
on the tower or on the remote  
remote. The fan will begin to oscillate from  
side to side.  
To stop the fan from oscillating, simply  
control unit.  
1.Press the auto off button once to switch  
the fan off after 1 hour. The light on the  
tower corresponding to the  
illuminate.  
position will  
press the  
button once again.  
2.Press the auto off button again to have the  
fan switch after 2 hours. The light on the  
tower corresponding to the  
illuminate.  
position will  
3.Similarly, pressing the auto off button a 3rd  
or 4th time will set the fan to switch after 4  
or 8 hours respectively. The corresponding  
light on the tower  
accordingly.  
or  
will illuminate  
To cancel the setting, keep pressing the auto  
off button until it cycles past 8 hours and  
returns to its normal setting. The auto off  
timer will be deactivated, the timing light will  
be off, and the fan will remain on until it is  
switched off manually.  
10  
 
Using Your Tower Fan (continued)  
Nature mode  
Sleep mode  
Nature mode provides an extra level of  
comfort by simulating the natural rise and fall  
of the wind over time. You can use this mode  
on any fan speed setting.  
To use Nature mode:  
1.Choose a fan speed.  
Sleep mode is identical to Nature mode with  
the added advantage that the highest fan  
speed gradually decreases over time. This  
allows you to turn the fan on a high speed  
setting last thing at night, knowing that by  
the time you are asleep, the fan has switched  
itself down to a slower speed.  
2.Press the  
the remote until the  
button on either the tower or  
light illuminates.  
To use Sleep mode:  
1.Choose a fan speed.  
The fan will now vary its speed every few  
seconds between the chosen fan speed, each  
lower fan speed, and off. For example, if you  
set the fan speed to 2 (medium), the actual  
fan speed will alternate between 2, 1 and off.  
2.Press the  
the remote until the  
button on either the tower or  
light illuminates.  
The fan will now operate in the same manner  
as with Nature mode, except that after 30  
minutes, the maximum speed will decrease.  
Eventually in this mode, the fan switches  
down to 1 (low) speed, which alternates  
between 1 and off.  
To cancel Nature mode, Press the  
button  
on either the tower or the remote until the  
light is no longer illuminated.  
To cancel Sleep mode, Press the  
button  
on either the tower or the remote until the  
light is no longer illuminated.  
11  
 
Troubleshooting Guide  
If your tower fan fails to operate check the  
following:  
If your remote control fails to operate check  
the following:  
Make sure the electrical outlet or circuit  
breaker is working.  
Ensure that you point the remote towards the  
front of the fan.  
Check for obstructions around the air intake  
grill.  
Check that the batteries are not worn.  
Replace if necessary.  
Care And Cleaning  
Ensure that your fan is switched off and  
disconnected from the power outlet before  
cleaning.  
Take care that excessive dust does not build  
up in the air-intake and air-outlet grill, and  
clean it occasionally using a dry brush or  
vacuum cleaner.  
Store the fan in a cool dry place when not in  
use, in its original carton if possible.  
Carefully wipe your fan using a clean cloth.  
Do not use abrasive cleaners or brushes to  
clean the appliance as these may scratch the  
surface.  
12  
 
2 Year Replacement Guarantee  
We are so condent of the quality of our product, should this  
appliance develop any malfunction within 2 years of purchase  
(3 Months commercial use) due to faulty materials  
or manufacture, we will replace it for you absolutely free.  
Should you experience any difculties  
with your appliance, please phone our  
free call customer service line for advice  
on 1300 881 861 in Australia, or 0800  
786 232 in New Zealand.  
Sunbeam Service Centres  
Sunbeam has established a network of  
authorised service centres throughout  
Australia and New Zealand to provide  
quick, convenient service for our  
customers.  
Alternatively, simply return the faulty  
appliance to your place of purchase,  
along with your purchase receipt.  
Should your appliance require repair  
or service, either during or after the  
guarantee period, contact your nearest  
service centre.  
Your Sunbeam 2 Year Replacement  
Guarantee naturally does not cover  
misuse or negligent handling, and  
excludes breakables such as glass or  
ceramic items, and normal wear and tear.  
For a complete list of Sunbeam’s  
authorised service centres:  
Australia  
Similarly, your 2 Year Replacement  
Guarantee does not cover damage to  
household surfaces as a result of water  
or other substances leaking from your  
appliance, nor does it cover freight costs.  
1300 881 861  
New Zealand  
0800 786 232  
In Australia, this guarantee is additional  
to the conditions and guarantees which  
are mandatory as implied under the  
Trade Practices Act 1974 and State and  
Territory legislation.  
13  
 
Consumer Hotline  
In Australia  
Or call 1300 881 861  
In New Zealand  
Or call 0800 786 232  
is a registered Trademark of Sunbeam.  
Made in China.  
Due to minor changes in design or otherwise,  
the product may differ from the one shown in this leaet.  
© Copyright Sunbeam Corporation Limited 2008.  
ABN 45 000 006 771  
0708  
Sunbeam Corporation is a division of GUD Holdings Ltd.  
 

Sharp All in One Printer FO DC500 User Manual
Sharp CRT Television Cx68n5 User Manual
Sigma Digital Camera SD14 User Manual
Snapper Lawn Mower ZU2014K User Manual
Snapper Snow Blower SE5203 User Manual
Sony Ericsson Cell Phone W550i User Manual
Sony MP3 Player RDR VX530 User Manual
Speco Technologies DVR 4TN User Manual
Spin Master Motorized Toy Car Gyro Force User Manual
Sub Zero Door 3756430 User Manual