Swann Door MWMA170510E User Manual

Advanced security made easy™  
Wireless Mat  
Doorchime  
SW351-WMA  
Operating Instructions  
SW351-WMA  
MWMA170510E  
 
Operation  
Changing Batteries  
Each of the three devices - the mat, the doorbell and the chime unit - are powered by batteries.  
The mat and the doorbell each require a 12V A23 battery.  
The chime unit requires 3 x AA cells (for a total of 4.5V).  
Changing the Chime Tone  
You can set the chime unit to emit one sound when the doorbell is pressed, and a different tone when  
someone steps on the mat. This is useful if you use the mat and doorbell for different entrances - each  
one can have its own sound!  
DIP Switches and Jumper Settings  
Jumpers control the wireless frequency which the doorbell and mat use to communicate with the chime  
unit. For the system to function correctly, the mat, doorbell and chime unit must have the same  
arrangement of jumpers. The default configuration is for all jumpers to be closed (that is, they have  
the black clip attached).  
The DIP switches change the tone which the Chime Unit will sound when the mat or doorbell is  
triggered. The sounds that you can choose from, and the arrangement of switches to access them are:  
ON  
ON  
None  
Classic Doorbell  
Loud Bell  
1
2
1
2
ON  
ON  
Church Bells  
1
2
1
2
To access the battery compartment, jumper pins and DIP switches of the Wireless Mat control  
unit:  
1. Remove the Wireless Mat control module from the small pouch.  
2. Insert a screwdriver or similar into the locking tab on the top of the doorbell casing, and press  
down to release the locking tab.  
3. The battery is located at the base of the control module. The jumper pins and the DIP switches  
are located immediately above.  
Jumper Pins  
DIP Switches  
To access the battery, jumper pins and DIP switches  
inside the doorbell:  
1. Insert a screwdriver or similar into the locking tab  
on the top of the doorbell casing, and press down  
to release the locking tab.  
2. Remove the doorbell from the rear plate. The  
jumpers, DIP switches and battery are located  
within.  
To access the jumper pins in the Chime Unit:  
Jumper Pins  
1. Locate the jumper compartment cover on the rear of  
the chime unit - its the small compartment above and  
slightly left of the battery compartment.  
2. Using a small Phillips-head screwdriver, remove the  
screw and lift the compartment cover. The jumpers are  
located within.  
3. Note that there are no DIP switches in the chime unit.  
3
 
Helpdesk / Technical Support Details  
Swann Technical Support  
All Countries E-mail: [email protected]  
Telephone Helpdesk  
USA toll free  
1-800-627-2799  
AUSTRALIA toll free  
1300 138 324  
(Su, 2pm-10pm US PT)  
(M-Th, 6am-10pm US PT)  
(F 6am-2pm US PT)  
USA Exchange & Repairs  
1-800-627-2799 (Option 1)  
(M-F, 9am-5pm US PT)  
(M 9am-5pm AUS ET)  
(Tu-F 1am-5pm AUS ET)  
(Sa 1am-9am AUS ET)  
NEW ZEALAND toll free  
0800 479 266  
UK  
0203 027 0979  
current time in Melbourne, Australia compared to your local time.  
Warranty Information  
Swann Communications LTD.  
Swann Communications USA Inc.  
Swann Communications  
Unit 13, 331 Ingles Street,  
Port Melbourne Vic 3207  
Stag Gates House  
63/64 The Avenue  
SO171XS  
12636 Clark Street  
Santa Fe Springs CA 90670  
USA  
United Kingdom  
Swann Communications warrants this product against defects in workmanship and  
material for a period of one (1) year from it’s original purchase date. You must pres-  
ent your receipt as proof of date of purchase for warranty validation. Any unit which  
proves defective during the stated period will be repaired without charge for parts or  
labour or replaced at the sole discretion of Swann. The end user is responsible for all  
freight charges incurred to send the product to Swann’s repair centres. The end user is  
responsible for all shipping costs incurred when shipping from and to any country other  
than the country of origin.  
The warranty does not cover any incidental, accidental or consequential damages aris-  
ing from the use of or the inability to use this product. Any costs associated with the  
fitting or removal of this product by a tradesman or other person or any other costs  
associated with its use are the responsibility of the end user. This warranty applies to  
the original purchaser of the product only and is not transferable to any third party.  
Unauthorized end user or third party modifications to any component or evidence of  
misuse or abuse of the device will render all warranties void.  
By law some countries do not allow limitations on certain exclusions in this warranty.  
Where applicable by local laws, regulations and legal rights will take precedence.  
© Swann Communications 2010  
 

Sharp Computer Monitor PN R903 User Manual
Snapper Lawn Mower Zero Turning Z Riding User Manual
Soleus Air Electric Heater HGW 308 User Manual
Sony Car Stereo System NWZ A815 A816 A818 User Manual
Sony DVD Recorder 4 131 978 111 User Manual
Sony Speaker System CMT CP505MD User Manual
SVA Security Camera CDR 1206 User Manual
Sylvania Flat Panel Television SRT902A User Manual
Tannoy Cell Phone T303 User Manual
Targus Mouse 400 0088 001A User Manual